A well designed fan mount + wind duct + add on provision for many 3d printer hot ends.
設計周全的冷卻風扇管架，適用於多種印頭，創想的CR系列，Ender系列都可。
A good design must
一個好的設計應該是
1. Efficient on cooling好的冷卻效果
§ Hot end cooling duct conformed from fan blade circle to heat sink rectangle, making 100% air go through heat sink.由風扇旋轉的圓形，變化成消熱塊的方形，使得空氣100%通過消熱塊。
§. Filament cooling fan partially share duct wall with hot end cooling duct to shorten the distance from fan to duct outlet so not to lost too much pressure.印材冷卻風扇管部份與印頭適形壁共用，減少風扇到出風口的距離，以免損失風壓。
§ The filament cooling duct pointing bullseye to hot end tip from both sides.印材冷風出風口由兩側直對印頭。
§. Filament cooling fan is placed in high place so to take cooler up above air.印材冷卻風扇置於高處，吸進較冷空氣。
§ Hot end cooling fan is placed as high as it can be and with an optional hot air defender.印頭冷卻風扇稍提高，配上選用的熱氣擋。
2. Easy to print.列印容易
§ One print does it all.單件列印，包含所有功能。
§ It is designed with “easy to print” in mind. You need to have support while printing, but the support is only 4mm high.專為簡單列印設計，只需要4mm高的支撐(無需內部支撐)。
§ Bridging is reduced to very short distance so you won’t fail on that. It’s difficult to fail when printing them.橋接已小到很難失敗的程度。
§ Two hooves in front of duct ends is for better adherence to print bed and you should cut them off after finish printing.出風口的兩個"蹄"，是為了列印着床而有，印完就應把它剪掉。
§ You can either remove or leave the support on. It won’t affect the installation.支撐可留，可去，不影響安裝。
3. Light in weight, compact in size, sturdy in structure.重量輕，尺寸小，結構強
§ All 4 models are less than 20 grams.四個設計都不到20克。
§ With conformal duct design, greatly shrink the dimension needed without sacrificing any performance.在適形風管設計下，尺寸大為縮小，但不犧牲任何功能。
§ Because it is compact, it is quite sturdy. The thick of the screw holes is 4mm.緊緻的尺寸使得它變得強固，鎖螺絲的部分厚達4mm。
4. Easy to install.安裝容易
§ Doesn’t need any screws except two for locking the hot end (with 4mm thick, you need longer ones).除了兩支較長的所印頭螺絲，其它螺絲都不要。
§ For all fans, you just insert them into their positions.冷卻風扇只要插入就好。
5. Fits for more different machines and requirements.適用多型機器，多種需求
§ The design is hot end depending rather than machine depending. As long as the two screw holes of hot end is between 14mm to 16mm, you can install it.此設計與機器的冷卻組合安裝螺絲孔無關，依印頭的螺絲孔設計。只要印頭螺絲孔在14mm 到 16mm都可安裝。
§ 4 different models to satisfy different requirements四型設計，以滿足不同需求
§§ 1(h.e. cooling fan) + 1(flm cooling fan)。一(印頭風扇) + 一(印材風扇)
§§ 1 + 1 + 2(add on provision mounting holes)。一 + 一 + 二(附加功能安裝孔)
§§ 1 + 2。一 + 二
§§ 1 + 2 + 2。一 + 一 + 二
6. Good visibility to print tip.看到印頭
§ Designed with that in mind, so you can monitor every moment of the printing.設計理念之一，可以很容易的監看印頭。
Thingiverse
http://www.thingiverse.com/thing:3256666
翻譯年糕
詹凱文
2018-12-05 00:10:31
請問內部需要支撐嗎
林佑臻
2018-12-05 00:50:39
ChihJun Soong
2018-12-05 07:27:36
John Ting
2018-12-05 07:33:19
Kevin Lan
2018-12-05 08:40:39
這個導風罩的設計是我看過數一數二用心的!
考慮到容易印, 容易裝(用原廠風扇不用另外買)等等, 真的厲害.
馬小將
2018-12-05 12:33:45
Wingo Lee
2018-12-06 20:20:00
太久沒玩打印機，下載了curs3.6無腦沒開支撐直接印
Wingo Lee
2018-12-07 13:45:06
Jeffrey Lee
2018-12-30 12:04:39
請問這個導風罩用PLA印可行嗎? (擔心耐熱問題，但考量會一直有風扇散熱，似乎又可行)
彭士瑋
2018-12-30 14:59:51
