Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Scott Fairburn
2019-03-06 18:36:47

Yesterday's print all painted.

翻譯年糕

Richard Thomas
2019-03-06 18:40:55

Jaco Norchie Nortje
2019-03-06 19:12:02

Susan Sioux Mercer
2019-03-06 19:34:03

Rolf Busetto
2019-03-07 16:46:27

原文網址 Scott Fairburn
2019-03-06 00:37:25

Just done. I'll paint up tomorrow.

翻譯年糕

Jaco Norchie Nortje
2019-03-06 05:42:38

Scott Fairburn
2019-03-06 05:45:23

Lewis Thompson-Milne
2019-03-06 05:54:39

Scott Fairburn
2019-03-06 05:59:08

Lewis Thompson-Milne
2019-03-06 05:59:34

Rolf Busetto
2019-03-07 17:32:26

原文網址 Scott Fairburn
2019-03-05 22:16:03

Recent prints. Finally getting into larger stuff now. Spiderman bust almost done.

翻譯年糕

Bjørn Haakon Hermanrud
2019-03-05 22:17:45

Scott Fairburn
2019-03-05 22:20:15

Brett Isaacs
2019-03-05 22:27:25

Scott Fairburn
2019-03-05 22:30:35

Brett Isaacs
2019-03-05 22:34:13

Scott Fairburn
2019-03-05 22:36:07

Bruno Lemos
2019-03-05 22:57:28

Scott Fairburn
2019-03-05 22:59:12

Bruno Lemos
2019-03-05 23:11:13

原文網址 Scott Fairburn
2019-02-02 04:47:04

Nothing amazing but finished printing and painting this

翻譯年糕

Mason Combs
2019-02-03 11:34:22

原文網址 Scott Fairburn
2019-01-30 22:18:09

Help

So I've not used the machine for a bit.
Yesterday I put on a new FEP and new resin.

First print failed stuck to FEP and plate.

Second print bookmark below, worked perfectly.

3rd to 6th prints all failed. All supports on Plate but mess on FEP.

7th and 8th the two wings below came out perfect.

Next up another supports on Plate and mess on FEP.

Any suggestions?

翻譯年糕

Gon Garcia
2019-01-30 23:45:34

Scott Fairburn
2019-01-30 23:46:42

Gon Garcia
2019-01-30 23:48:38

Scott Fairburn
2019-01-30 23:51:19

Gon Garcia
2019-01-30 23:55:00

Scott Fairburn
2019-01-30 23:56:36

Philipp Douglas
2019-02-02 13:36:38

Scott Fairburn
2019-02-02 14:03:45

Gon Garcia
2019-02-03 00:38:56

Scott Fairburn
2019-02-03 00:42:53

Mark Wardle
2019-02-03 01:18:14

Scott Fairburn
2019-02-03 02:01:37

原文網址 Scott Fairburn
2019-01-02 18:24:37

Tried 4 prints so far today all different. All stuck to FEP, where im i going wrong?
I was having a great success rate recently and cant think of any changes ive made.

翻譯年糕

Sen Kun
2019-01-02 18:28:06

Guti Gutmann
2019-01-02 18:31:21

Charlie Anderson
2019-01-02 18:43:05

Scott Fairburn
2019-01-02 18:44:44

Scott Fairburn
2019-01-02 18:45:35

Jannick Langfahl
2019-01-02 19:31:43

Thor Johnson
2019-01-02 22:30:21

Scott Fairburn
2019-01-02 22:39:35

Thor Johnson
2019-01-02 22:41:42

Steven Wood
2019-01-03 01:58:37

原文網址 Scott Fairburn
2018-10-27 20:11:52

So the other day I said I'd had my machine about 2 months.

About 70% perfect prints some possible human error.

I recently changed the FEP and did about 11 perfect prints. Then the next 3 were a bit off.

This morning I started using red resin instead of green and 4 perfect print runs.

Not too fussed, but it's very strange. All the time it's prints sticking to the fep instead of the plate or missed bits.

Flame tokens I did 5 minutes ago.

翻譯年糕

原文網址 Scott Fairburn
2018-10-23 05:15:52

I was getting loads of great prints. Then suddenly trying to print tokens for board games it was hit and miss. Tried lots of things then finally had that moment.

I'd been using the same FEP sheet since I got it a couple of months back. Changed it over and the last 11 runs have been perfect.

Did this lot today a few at a time in case of issues.

Tokens for mansions of madness in case anyone wanted to know.

翻譯年糕