Anycubic Photon Printer Owners 造訪社團

原文網址 Artur Fuste
2018-04-15 04:39:04

3 New settings thanks to Sante Chio, Fred Williams and Adrian Cyobanu.

翻譯年糕

原文網址 Jeremy Lauzon
2018-04-15 04:21:14

Model by mz4250

翻譯年糕

原文網址 Flint Read
2018-04-15 04:02:35

Julia von Pfaler has gone a bit quiet wonder what that clever metal worker is up to? Julia von Pfaler has gone a bit quiet wonder what that clever metal worker is up to? 翻譯年糕

原文網址 Say Andrea
2018-04-15 03:35:10

Clear resin + thermocromatic pigment. Worked better than I expected it to!

翻譯年糕

Mark Wardle
2018-04-15 03:47:13

Seb Jägermetal
2018-04-15 04:01:43

Ayman M. El Nigoumi
2018-04-15 05:34:38

Alessio Di Brigida
2018-04-15 10:12:09

Kevin McGuigan
2018-04-15 11:25:46

Say Andrea
2018-04-15 12:10:35

Say Andrea
2018-04-15 12:19:43

Robert Maki
2018-04-16 11:49:00

Say Andrea
2018-04-18 03:17:12

原文網址 Brian Jason
2018-04-15 02:52:50

Anyone know how to prevent this. I noticed this happens when i hollow out the model. I pretty much use default support settings and default setting for monocure rapid setting.

翻譯年糕

Mark Wardle
2018-04-15 03:12:58

Brian Jason
2018-04-15 03:13:27

Mark Wardle
2018-04-15 03:13:47

Brian Jason
2018-04-15 03:14:05

Mark Wardle
2018-04-15 03:14:12

Brian Jason
2018-04-15 03:15:15

Mark Wardle
2018-04-15 03:17:04

Philippe Maegerman
2018-04-15 03:22:16

Brian Jason
2018-04-15 03:26:07

Brian Jason
2018-04-15 03:26:20

Philippe Maegerman
2018-04-15 04:18:21

Brian Jason
2018-04-15 04:21:02

Philippe Maegerman
2018-04-15 04:21:38

Brian Jason
2018-04-15 04:26:56

Philippe Maegerman
2018-04-15 04:31:15

Brian Jason
2018-04-15 04:33:05

原文網址 Andy Levesque
2018-04-15 02:35:39

For those printing minis, do you hollow them out? If so, how thin of walls do you allow? I'm learning as I get ready for my first print and I'm having to go to .5mm to have any noticeable hollowing.

翻譯年糕

原文網址 Daniel Dulitzky
2018-04-15 02:04:24

time to get more resin
if you are in the USA
what is your favorite resin ?

翻譯年糕

原文網址 Brian Jason
2018-04-15 01:35:51

Well... woke up this morning and no smell! Well aside from a little stuffed up nose. But as of now. No smell and no light headache. Had to temporarily put the printer behind my table. Cause im still looking for a nice shelve or ikea lack set up for my cr10s s4 and photon...

The fan wasnt loud. My cr10 was more noisier. Left both printers printing all night. So this is a positive news.

As for the actual print... it's another story ? ? ? ? ?

翻譯年糕

原文網址 Leon Enriquez
2018-04-15 00:22:43

Hello, total newbie here! A couple of question if I may: 1. I'm having trouble adding support on some hanging areas (please see vid). It seems that im missing something that it doesnt add as it normally does on some areas? 2. any better recommendations for a software for preping your prints? How reliable are autoSupports (with intricate hanging layers)? TIA :)

翻譯年糕

原文網址 Roger Cejalvo II
2018-04-15 00:18:01

loving the monocure rapid clear so far, just a few questions. how can i clean a print and still keep it clear as possible? is it better being hollow or should i make it solid to help it keep clear even after cleaning. i notice IPA with a hollow clear print makes it very cloggy after. so maybe just cleaning the print with water only. just thought i would ask since i am still a noob. thanks

翻譯年糕