管理員
統計數據
原文網址 Andrej Andryi 2018-01-22 07:59:36
Hi, what is wrong here? First layer if 100% infill is ok, wallls are not good solid
ChienMing Liang 2018-01-22 08:16:51
Wrong wire diameter, set to 1.75
Andrej Andryi 2018-01-22 08:17:50
nozzle is 0.4mm and filament is set to 1.75mm
ChienMing Liang 2018-01-22 08:28:16
What kind of 3DP? CR10?
原文網址 Andrej Andryi 2016-01-14 08:35:34
Check this solid frame 3D printer, if you like it, support it:
原文網址 Andrej Andryi 2015-11-10 04:40:10
Hi all, im building new printer, but now, my hotend is still at 25 /210 celsius, it is not heating up, what can be problem? RED cable is first pin and BLACK is second pin in D10 part on ramps?
Ally Yao 2015-11-10 22:49:54
士瑋團長……求救！！
Andrej Andryi 2015-11-10 22:50:41
Head is not on last D10 PINS?
彭士瑋 2015-11-10 22:57:10
Andrej Andryi I did not find the D10. Which board you used?!
Andrej Andryi 2015-11-10 22:57:49
Im using RAMPS and MEGA2560
Andrej Andryi 2015-11-10 23:01:53
U isued D10 Pins (TOP of picture),not correct?
原文網址 Andrej Andryi 2015-08-25 16:18:43
Hi all, I saw lot of improvements on this CR7 3d printer, could you post some of that STL for it? for example i saw X-axis tension adjusting and others...has anyobdy list of it ?
林佑臻 2015-08-25 20:13:18
facebook searching is suck. I think it's better to upload to thingiverse.
Andrej Andryi 2015-08-25 20:15:24
ok, and do you have any zip with files for thingierse? we can upload them there...
原文網址 Andrej Andryi 2015-08-25 15:41:30
Hi, I just broke filamnt in teflon tube (white pipe), what to do? Im not able to take it out, i think, in this white tube my filament is too thick....
Andriy Chortya 2015-08-25 15:42:33
You probablyneed to disassemble the hot end.
Andrej Andryi 2015-08-25 15:45:09
yes, no problem with this... but 5cm of filament i have directly in white teflon tube... i can only cut this teflon tube (or where to buy new one?)
Andriy Chortya 2015-08-25 16:10:10
have you tried to push it with other fillament? or insert something like sponge and then push with other fillament and afterwards remove the sponge with thin wire.
Andriy Chortya 2015-08-25 16:10:18
post the foto
Neil Lan 2015-08-25 16:27:06
Post pic first
Andrej Andryi 2015-08-25 16:28:28
here is photo
Andriy Chortya 2015-08-25 16:29:13
why don't you pre-heat to PLA temp and push the fillament down?
Neil Lan 2015-08-25 19:05:29
If you have an air gun, that would be great to blow it out after heating.
原文網址 Andrej Andryi 2015-08-20 21:18:13
Do you have any cheap eshop in China or in Europe for all parts to CR-7 printer? I found of them in Europe, but all are very expensive for V-slots and especially for delrin v-wheels...
彭士瑋 2015-08-20 21:25:22
Where do you live? Germany?
Andrej Andryi 2015-08-20 21:25:52
Im liviing in Slovakia, and sometimes in Austria... Germany is not far for me...
Chuck Chu 2015-08-20 21:28:06
斯絡伐克
Chuck Chu 2015-08-20 21:28:18
在波蘭北部
Andrej Andryi 2015-08-20 21:29:25
In english or german please :) chuck chu...
Chuck Chu 2015-08-20 21:30:30
Slovakia chinese is 斯絡伐克
Chuck Chu 2015-08-20 21:31:06
In north Poland
Andrej Andryi 2015-08-20 21:31:26
Yes, but Slovakia is in south to Poland :)
林佑臻 2015-08-20 21:33:40
Accurately it's hard to find v-wheels in Taiwan....
Andrej Andryi 2015-08-20 21:34:51
Why so hard, taiwan is near to china, and china must have it...
彭士瑋 2015-08-20 21:38:35
How many people want this machine in your community . If you can buy ten machines. I believe delrin v-wheels are not a problem. you can ask them provide you for free. Or you want to collect the elements then build a CR-7 by your own!! LOL~
彭士瑋 2015-08-20 21:39:09
what is the average price of V-slot 3d printer you can get?
Andrej Andryi 2015-08-20 21:41:02
Yes, I want to build my own machines, better parameters, bigger size, auto leveling, or something very similar... average price is around 300usd, but whan I will buy parts...price can be around 200usd? not sure...
彭士瑋 2015-08-20 21:44:59
I just ask for u, U can get round 288 USD for one CR-7. (Shipping is included).
彭士瑋 2015-08-20 21:45:34
To have it first, then upgrade it!
Kevin Lan 2015-08-20 22:33:29
Actually I found delrin v-wheels and other OpenBuilds parts in Taiwan auction site. But I don't know if they have overseas posting services. http://class.ruten.com.tw/user/index00.php?s=soga172......
討論主題
全不選 常用關鍵字
