• COSPLAY 3D 建模
  • 3D列印服務
  • #maker+t=market
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Francesco Ostili
2020-03-27 00:30:02

Hello guys. I have the following problem stated here.
I have 3 photons and 2 of them Are giving me this problem at the end of every prints.
Each photon shares the same profile.
I have this kind of residue at the bottom of the vat all the time from 1 month apart.
The print doesn't fail but still I have to clean it.
Could it be possible that the lcd is going to stop working soon?
I have used these 2 printers for 6 months daily without replacing the LCDs.

All the suggestions are welcome.

+ I have got also sometimes this kind of problem: Smashed prints at the bottom. Not sure if they are related but still.

Room temp: 20°
0.05mm per layer
Prima creator resin

I even tried to bump the cooking time to 10 sec but nothing changed.

Thank you so much for all your help <3

翻譯年糕

Scott Hurd
2020-03-27 00:38:48

Could be pigment separation. Make sure you shake the bottle good and if you leave the resin in the vat for an extended time, stir it well.

Francesco Ostili
2020-03-27 00:48:35

I'll have a try!
Never thought about it.

Tony Tidwell
2020-03-27 12:14:00

Try using 3-in1 Multi-purpuse PTFE Lubricant on the inside botton of your vat. You can find a how to video on youtube. Basically just rub a fine coat on the bottom of the vat and it helps prevent resin sticking. If it does stick it is a lot easier to clean up.


原文網址 Francesco Ostili
2019-11-25 23:11:36

Hello guys!

I have got a question:

Anycubic support sent me a main board replacement for my anycubic (standard model, not S) yesterday.

After plugging it in everything worked like usual, blue menu buttons with white background.

After 2 on-off everything changed without any clue.

Now I have got a boot in with photon logo in red with white background, menu button in yellow with black background.

I guess that they sent me an anycubic S main board.

Now can I print with this new printes using the same sw/setting/everything else I used before?

Like photon validator, chitubox with the same values etc.

Thank you so much for your support and help <3

翻譯年糕

Bob Deblier
2019-11-25 23:16:56

Francesco Ostili
2019-11-25 23:36:27

Bob Deblier
2019-11-25 23:38:12

Francesco Ostili
2019-11-25 23:38:42

Bob Deblier
2019-11-25 23:39:14

Francesco Ostili
2019-11-25 23:42:14

Nick Young
2019-11-25 23:46:26


原文網址 Francesco Ostili
2019-06-01 16:35:21

Guys this is the chitubox download page .-.
Do you know where I can find the installer or where I can download it because it has been 3 days since I can't install it .-.
Thank you so much!

翻譯年糕

Tamás Lehoczky
2019-06-01 16:37:03

Andrey Sabrev
2019-06-01 16:38:33

Francesco Ostili
2019-06-01 16:47:06


原文網址 Francesco Ostili
2019-05-30 05:37:29

Hello guys. So finally my first print. After 3 failures I managed to level the build plate and then I got this.
Fine after all but as you can see from the photo, that lines are wierd.
What could it be?
Before this last print I noticed that the previous one left some prints mark on the Fep, like a Halo where then failed print got stuck to the fep.
Could it be this?

Thank you for all your help. If I'm at this point it's because of this group's lore ❤️

翻譯年糕

3Dprintingcorner
2019-05-30 05:41:24

Richard Shapiro
2019-05-30 05:42:14


 

討論主題

全不選 常用關鍵字