Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Jason Sankovitch
2019-07-18 11:12:32

Is it possible to use a model drafted in inches in chitubox?

翻譯年糕

Sen Kun
2019-07-18 11:37:29

Susan Sioux Mercer
2019-07-18 16:22:40

Chris Miller
2019-07-18 18:45:57

原文網址 Jason Sankovitch
2019-07-04 02:41:32

Looking for help with supports. I've watched videos and done some research, but I can't seem to figure out if what I'm seeing is normal, or if there is some setting I'm not tweaking. Essentially, I get a ton of islands when slicing with Chitubox. Some are extremely obvious. For example, the barrel of the gun in the attached photo does not get an automated support generated no matter what setting I use. So my current flow is to slice in Chitubox, find spots myself, then run through the validator and then manually clean up what it can't do automatically. Am I making my life harder than it needs to be? Is this something that is just the way it works with minis? Any advice is greatly appreciated.

imgur.com/a/SBnz3hE

翻譯年糕

Jason Sankovitch
2019-07-04 02:44:27

Tim Moulton
2019-07-04 02:45:25

Jason Sankovitch
2019-07-04 02:47:20

Tom Smith
2019-07-04 02:51:57

Michael Szita
2019-07-04 02:53:33

Jason Sankovitch
2019-07-04 02:53:46

Jeff Wand
2019-07-04 08:19:23

Jake Hamlin
2019-07-04 08:22:07

Jeff Wand
2019-07-04 08:33:14

Jason Sankovitch
2019-07-04 09:10:22

原文網址 Jason Sankovitch
2019-07-01 11:57:42

Looking for some recommendations for “must print” models that show off what this printer can do (vs, say, an fdm).

翻譯年糕

Brandon Marcussen
2019-07-01 12:15:06

Jason MeGahee
2019-07-01 12:43:12

Peter Ede
2019-07-01 14:09:36

Ethan Brown
2019-07-01 14:31:01

原文網址 Jason Sankovitch
2019-07-01 09:24:55

Does anyone know where I can find the MSDS for the Anycubic translucent resin? Seeing a lot of alarming things out there and want to read up on some facts.

翻譯年糕

Scott Pavlich
2019-07-01 09:30:22

Jason Sankovitch
2019-07-01 09:33:59

Neil Ramsay
2019-07-01 09:39:04

Neil Ramsay
2019-07-01 09:40:28

Travis McGeathy
2019-07-01 10:03:40

Scott Pavlich
2019-07-01 10:17:01

Jason Sankovitch
2019-07-01 10:18:09

Jason Sankovitch
2019-07-01 10:19:32

Scott Pavlich
2019-07-01 10:23:13

Travis McGeathy
2019-07-01 10:23:50

Scott Pavlich
2019-07-01 10:35:20

Jared Daniel Nielsen
2019-07-01 10:37:34

原文網址 Jason Sankovitch
2019-06-30 05:02:51

Hi everyone! I attempted my first print and had bed adhesion problems. No biggie, I'll try leveling again. However, I'm curious about what exactly I found in the vat. The circle base of the test model was stuck to the film. As you can see in the picture, there was a much larger chunk of cured resin as well - much larger than anything that should have been exposed. Is this the result of the poor adhesion or something else? I was printing the test cube directly off of the USB that came with the printer (no change to settings).

翻譯年糕