Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Justin Cupitt
2020-02-29 06:29:34

H ey all, printed off some of these Remixed Tau guns for a friend and thought they were too nice not to share.

Link in comments. 翻譯年糕

Justin Cupitt
2020-02-29 06:29:44

原文網址 Justin Cupitt
2019-12-08 15:16:21

Hey All, been having a few issues with Monocure Grey being overly brittle/soft (kind of hard to describe) when it is just out of the printer. While this is great for removing supports it tends to be problematic when fine details came appart when just rinsing in ipa. Settings are 8s exposure @0.03. Take note that once post cured the parts are just fine and no longer tacky as you may expect with a dud batch or resin.

翻譯年糕

Ben Gill
2019-12-08 15:22:33

Justin Cupitt
2019-12-08 15:29:27

David Jericho
2019-12-08 18:07:03

Justin Cupitt
2019-12-08 18:19:17

原文網址 Justin Cupitt
2019-12-07 09:02:11

Sharon Apple Virturoid from Macross Plus. File from thingiverse, hollowed and printed at .03 in Monocure Grey.

When it printed it had a few little defects due to air bubbles in my roughly shaken resin (my bad), also it come close to detaching from the plate due to suction. If I ever print another I think I would want to tweak the base layers or not be lazy with supports. I printed it flat on the plate to avoid post cleanup but of course that meant there was no way for the hole to allow suction release. Remember guys always think about hollow models and suction issues when you set up your prints.

Looks kind of good with some paint on though.

翻譯年糕

Stefan Giudici
2019-12-07 09:14:30

Justin Cupitt
2019-12-07 09:15:52

Justin Cupitt
2019-12-07 09:16:48

Jack Hydrazines
2019-12-07 09:24:53

Jack Hydrazines
2019-12-07 09:25:26

原文網址 Justin Cupitt
2019-11-12 16:25:00

Just curious, what sort of settings were people using for Monocure Rapid Grey.

Edit: Before anyone asks I have had a look at the comparator doc. I'm more interested in what results people are getting that aren't listed on there.

翻譯年糕

Scott Roberts
2019-11-12 17:30:30

Justin Cupitt
2019-11-12 18:00:38

Scott Roberts
2019-11-12 18:01:48

Justin Cupitt
2019-11-12 18:04:42

Scott Roberts
2019-11-12 18:20:05

Tiago Lopes
2019-11-12 18:23:33

Scott Roberts
2019-11-12 18:31:24

Scott Roberts
2019-11-12 18:31:32

Justin Cupitt
2019-11-12 19:22:49

原文網址 Justin Cupitt
2019-09-18 15:35:08

Remixed the AT Quake cannon that can be found on thingiverse by changing the elbow mount, adding some cables and detailed armour plates. I did leave it in the post cure station a little long due to a phone call, so it is slightly discoloured but otherwise not too bad. Printed in Anycubic Grey at .03.

翻譯年糕

Chris Beaumont
2019-09-18 15:37:34

Justin Cupitt
2019-09-18 15:39:34

Sean Poeschl
2019-09-18 23:17:29

Sean Poeschl
2019-09-18 23:17:40

Joel Mendoza
2019-09-19 09:10:04

Justin Cupitt
2019-09-19 09:32:09

Michael Szita
2019-09-19 11:17:51

Joel Mendoza
2019-09-19 11:18:28

Michael Szita
2019-09-19 11:19:12

原文網址 Justin Cupitt
2019-08-28 18:05:40

So technical advice guys, put the new screen that finally arrived in the Photon that was giving screen errors out of the box. Now it doesn't send anything to the screen when running the test and gives error tones on startup. Any ideas? Is it a main board fail out of the box? Could it be a dodgy lcd connector on the main board?

It seems a bit of a strange error to be presenting after something as simple as an lcd replacement.

Edit: Please note that the new screen was a warranty replacement as this unit had issues out of the box.

Edit 2: Ok so flashed the firmware and got rid of the other errors, but the problem with the screen persists. Looks like it's time to email support back again.

翻譯年糕

原文網址 Justin Cupitt
2019-08-16 08:00:17

Hard to get photos but I'd call these head swaps for Titanicus Knights a success.

翻譯年糕