• #maker+t=market
  • 3D列印服務
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Phil Hays
2019-08-06 08:56:27

Photon S owners:

Has anyone run the new Photon Workshop v2.0.23 and the RERF file?

I installed the firmware update then opened the RERF file (no alterations allowed) and here's what I got! I can't make heads or tails of the results. And why!? oh why do some of the shapes skew and the base curl up?

Anycubic Gray resin was used. I have had several successful prints before this update.

(I did NOT re-level my bed after the update... was that a mistake?)

翻譯年糕

Jon Carroll
2019-08-06 09:05:05

Ben Marquez
2019-08-06 09:09:26

Stuart Taylor
2019-08-06 20:00:05

Chris Graf
2019-08-06 20:09:27


原文網址 Phil Hays
2019-07-28 01:18:09

COJOINED SUPPORTS!

UPDATE:

Thanks for all the suggestions! I redid my parts twice more, adjusting Support settings and Exposure times per your recommendations (Normal Exp @12, bottom @ 80).

Although things looking better there are till a few small details to correct: why is the end nearest the base drooping/distorting and an edge losing its "edge" (A & B)? What did I do to the supports to cause the divots (C)? See pictures

==========================================

The good news: my Photon S is properly leveled and I have been able to make a few prints.

The bad news: I tried CHITUBOX for adding supports as some have recommended (see photos) and I (foolishly?) used AUTOSUPPORT. I then saved the STL and used Photon Workshop to SLICE it. The screen shots clearly show open space between the supports and a decent number of supports.

So WHY are the supports on the prints all cojoined and massed? What did I do wrong?

And, man!, is that resin solid!!

>Anycubic Grey @

Normal Exposure(s): //18// 12

Off Time(s):1

Bottom Exposure(s): //100// 80

Bottom Layers:8

Z Lift Distance(mm):4

Z Lift Speed(mm/s):3

Z Retract Speed(mm/s):3

翻譯年糕

Andy Tellier
2019-07-28 01:20:06

Adrian M. Neville
2019-07-28 01:20:11

Conor Tanji
2019-07-28 01:22:06

Aaron Marino-Drake
2019-07-28 01:22:28

Michael Cargile
2019-07-28 01:24:28

Alex Hines
2019-07-28 01:25:43

Michael Cargile
2019-07-28 01:25:51

Niklas Rosenkilde
2019-07-28 01:27:34

Rigo Arevalo
2019-07-28 01:34:53

Daniel Hoke
2019-07-28 01:36:28

Simon Gamble
2019-07-28 01:57:45

Jon Carroll
2019-07-28 01:58:59

Bob Deblier
2019-07-28 03:01:24

Michael Wöss
2019-07-28 03:19:16

Sue Parks
2019-07-28 03:21:19

Greg Chapman
2019-07-28 03:51:35

Greg Chapman
2019-07-28 03:53:15

Phil Hays
2019-07-28 04:20:21

Phil Hays
2019-07-28 04:21:14

Phil Hays
2019-07-28 04:22:53

Phil Hays
2019-07-28 04:25:00

Jon Carroll
2019-07-28 04:32:04

Bob Deblier
2019-07-28 04:32:16

Jon Carroll
2019-07-28 04:32:58

Phil Hays
2019-07-28 04:33:56

Bob Deblier
2019-07-28 04:34:33

Phil Hays
2019-07-28 04:35:23

Phil Hays
2019-07-28 04:36:04

Chris McDermott
2019-07-28 05:03:02

Sue Parks
2019-07-28 05:29:09

Colin Graham
2019-07-28 06:14:28

Mike Fatchett
2019-07-28 06:14:28

Arthur Withier
2019-07-29 00:27:07


原文網址 Phil Hays
2019-07-22 11:55:30

PRINT FAIL: I ran a couple of models today and 3/4 way thru I saw there was nothing on the plate! I thought I might have effd my plate by tightening the grub screw while cleaning after my first two successful prints. I thought maybe my drawings/stls might be effd up... when I went to clean up I discovered the bases of my models stuck to the top of the FEP (was able to remove with plastic scraper, whew!). What am I doing wrong?

Using AnyCubic Neutral Grey and settings found here:

Normal Exposure(s):18

Off Time(s):1

Bottom Exposure(s):100

Bottom Layers:8

Z Lift Distance(mm):4

Z Lift Speed(mm/s):3

Z Retract Speed(mm/s):3

翻譯年糕

Nick Williams
2019-07-22 11:59:54

Phil Hays
2019-07-22 12:05:16

Nick Williams
2019-07-22 12:07:48

Phil Hays
2019-07-22 12:11:58

Nick Williams
2019-07-22 12:12:46

Nick Williams
2019-07-22 12:13:17

Nick Williams
2019-07-22 12:14:02

Nick Williams
2019-07-22 12:14:21

Nick Williams
2019-07-22 12:14:49

Nick Williams
2019-07-22 12:15:27

Phil Hays
2019-07-22 12:17:24

Phil Hays
2019-07-22 12:20:04

Nick Williams
2019-07-22 12:20:57

Nick Williams
2019-07-22 12:21:05

Phil Hays
2019-07-22 12:23:46

Mike Fatchett
2019-07-22 12:37:41

Susan Sioux Mercer
2019-07-22 12:46:39

Susan Sioux Mercer
2019-07-22 12:47:46

Phil Hays
2019-07-22 12:48:17

Mike Fatchett
2019-07-22 12:48:35

Phil Hays
2019-07-22 12:53:25

Susan Sioux Mercer
2019-07-22 13:03:12

Susan Sioux Mercer
2019-07-22 13:04:46

Bob Deblier
2019-07-22 17:11:09

Mike Fatchett
2019-07-22 22:58:06

Phil Hays
2019-07-22 22:59:00

Bob Deblier
2019-07-22 23:00:00

Bob Deblier
2019-07-22 23:00:59

Phil Hays
2019-07-22 23:03:40

Bob Deblier
2019-07-22 23:04:14

Phil Hays
2019-07-23 05:15:19

Phil Hays
2019-07-23 05:28:06

Phil Hays
2019-07-23 05:29:59


原文網址 Phil Hays
2019-07-22 02:49:11

PROBLEM SOLVED! Thanks everyone!!

So I created this component for a 1/32 scale model in Autodesk Inventor, saved it as a .stl but cannot load it in the Photon (S) WorkShop. My PC display says its "loading" but then nothing appears in the build box. What am I doing wrong? Is it the level of detail that WorkShop can't resolve? ?

翻譯年糕

Hamza Doğan
2019-07-22 02:56:06

Henry Laubscher
2019-07-22 04:00:45

Phil Hays
2019-07-22 05:11:18

Henry Laubscher
2019-07-22 05:42:30

Oliver Devereux-Burden
2019-07-22 05:42:58

Phil Hays
2019-07-22 11:25:29

Kuba Świeciński
2019-07-22 16:37:21

Phil Hays
2019-07-23 05:38:25

Phil Hays
2019-07-23 05:39:09


原文網址 Phil Hays
2019-07-22 00:39:17

Anyone here use Autodesk Inventor and/or Fusion 360 for CAD design? I teach a high school engineering classes (PLTW) and my students and I use this and want to create designs for our 3D printers at school. I am also a hobbyist and want to design my own stuff using my Photon S at home.

翻譯年糕

Gazsó Péter
2019-07-22 00:44:42

Brian Wright
2019-07-22 00:59:07

Kuba Świeciński
2019-07-22 01:03:59

Stefan Giudici
2019-07-22 01:06:04

Phil Hays
2019-07-22 13:02:20

Marcin Kudzia
2019-07-22 19:09:47

Jason Dentler
2019-07-22 19:55:25

Jao Au Pinto
2019-07-22 21:22:24

Phil Hays
2019-07-22 22:55:42


原文網址 Phil Hays
2019-07-15 23:29:17

Newbie here: I've read a lot of posts re: frequency tuning of the FEP. I've scrolled a LOT of posts but cannot find any link or name citation to an app for this. Suggestions? ?

翻譯年糕

Fedor Pikus
2019-07-15 23:56:33

Melecio Guzman
2019-07-16 00:00:49


 

討論主題

全不選 常用關鍵字