Anycubic Photon Printer Owners 造訪社團

原文網址 Byc Bernardo
2019-09-21 23:43:13

Installation of a camera inside the confines of one Photon S.

The camera is with a pi zero W in a Raspberry box. Notes above, a temperature and hygrometry sensor that I use to control the heating of the housing so that the resin is at a good temperature.

Instalación de una cámara dentro de la caja de un Photon S.

La cámara es con un pi zero W en una caja de Raspberry. Notas arriba, un sensor de temperatura e higrometría que utilizo para controlar el calentamiento de la carcasa para que la resina sea a buena temperatura.

Installation d'une caméra à l'intérieur de l'enceinte de la Photon S.

La caméra est avec un pi zero W dans un boîtier Raspberry. On remarque au-dessus, un capteur de température et hygrométrie que j'utilise pour contrôler le chauffage de l'enceinte afin que la résine soit à bonne température.

翻譯年糕

William Boshoff
2019-09-22 20:19:00

Byc Bernardo
2019-09-23 03:18:54

原文網址 Gabriel Marian Alfons
2019-09-21 23:18:59

The best in town!!! £4.29 250 microns, 20 sheets = 80 film change!! 125 microns per sheet ? ? ?

To make them transparent I used a hot air gun from my wife...

翻譯年糕

Stefan Lukus
2019-09-21 23:59:30

Gabriel Marian Alfons
2019-09-22 00:11:02

Stefan Lukus
2019-09-22 00:15:19

Gabriel Marian Alfons
2019-09-22 00:19:08

Stefan Lukus
2019-09-22 00:21:39

Gabriel Marian Alfons
2019-09-22 00:22:27

Frank Seel
2019-09-22 03:33:30

Gabriel Marian Alfons
2019-09-22 04:15:23

George Bulte
2019-09-22 07:36:22

Derek Reihe
2019-09-22 08:28:47

Gabriel Marian Alfons
2019-09-22 22:00:34

原文網址 James Byberg
2019-09-21 23:18:53

Keep having this fail like this. Print runs fine for an hour, then seemingly gets pulled off the build plate and I'm noticing a lot of extra crud around it after it fails. Guessing that I need to change the fep?

翻譯年糕

Dustin Scott
2019-09-21 23:20:37

James Byberg
2019-09-21 23:21:40

James Byberg
2019-09-21 23:24:24

Dustin Scott
2019-09-21 23:26:12

Ryan Mitchell
2019-09-21 23:34:18

Jarrod Smith
2019-09-21 23:36:08

James Byberg
2019-09-21 23:40:28

James Byberg
2019-09-21 23:51:41

James Byberg
2019-09-22 00:13:25

Jarrod Smith
2019-09-22 00:33:21

James Byberg
2019-09-22 00:34:28

原文網址 Ricardo Sebastian Ibacache Guerr
2019-09-21 23:05:58

So my new fep didn't came with protection film, and I was going crazy

翻譯年糕

Ricardo Sebastian Ibacache Guerr
2019-09-21 23:30:43

Jonathan Alvarado
2019-09-21 23:39:17

Adan Mouriño
2019-09-22 08:03:50

Adan Mouriño
2019-09-22 08:04:00

原文網址 Sean Evans
2019-09-21 23:02:29

HO Movietrucks is nearing it's first product!
Project Rubber Duck progresses slowly but surely (Project Duel is almost complete, just waiting for the final production prototype of the tanker to finish printing).
I'm impressed by the 'standard' resolution of my Photon. Here's my 1/87 scale Mack R700 cab prototype with a custom addition...

翻譯年糕

原文網址 Nicholas Piper
2019-09-21 22:30:35

Help! Today my photon started printing models mirrored/reversed. I haven't changed any settings from 2 weeks ago (last time I printed). I have read through the posts and tried the suggestions but no joy. I'm using Chitubox as the slicer and nothing like this happened previously. Any new suggestions welcome.

翻譯年糕

Chad Elstad
2019-09-21 22:33:31