Anycubic Photon Printer Owners 造訪社團

原文網址 Josh Ujak Lijewski
2019-09-10 14:16:39

Ok, I found where to input my different resin settings in ChiTuBox. However it always defaults to the same resin. How do I select my other resin settings?

翻譯年糕

Mike Kelso
2019-09-10 14:35:46

Josh Ujak Lijewski
2019-09-10 15:06:44

原文網址 Nigel Davies
2019-09-10 14:08:04

What would cause a fail in this way?
I had 6 successful prints back to back. Same settings each time.
Then this happens there's just a big chunk missing from the centre of each print.

If it makes a difference the failed part of each was facing the centre of the bed

翻譯年糕

Shane Johnson
2019-09-10 15:02:01

原文網址 Fulvio Massimo Mariani
2019-09-10 13:15:43

First mini

第一個迷你

· 查看原文 · 為此翻譯評分

原文網址 Itai M Lustgarten
2019-09-10 13:13:37

for those of you who like to share here are my settings for fast Siraya gray fast in 0.03. for those who like to send us all to the exposure test I say, better an experience of another as a starting point, worst case scenario one changes the exposure time.... 翻譯年糕

Shane Johnson
2019-09-10 13:17:34

Itai M Lustgarten
2019-09-10 13:41:36

Shane Johnson
2019-09-10 13:59:00

Itai M Lustgarten
2019-09-10 15:29:59

Itai M Lustgarten
2019-09-10 15:37:16

Ryan Myers
2019-09-10 19:53:34

原文網址 Jagmeet Singh
2019-09-10 12:43:43

原文網址 Nick Hough
2019-09-10 12:27:20

Hello! Looking for advice. I’ve been able to print a few successful miniatures from Artisan Guild. I attempted to print their bigger troll model and it failed. I tried leveling it two times now and still get the same thing. Do my settings seem correct?

Photon S

Anycubic Grey for resin.

翻譯年糕

Arnold Styvens
2019-09-10 12:36:01

Greg Kourakos
2019-09-10 12:38:05

Jake Gilmore
2019-09-10 13:08:24

Richard Webb
2019-09-10 13:17:40

Szymon Ulenberg
2019-09-10 17:17:19

Nick Hough
2019-09-10 19:34:33

Nick Hough
2019-09-10 19:37:03

Greg Kourakos
2019-09-10 19:43:00

Nick Hough
2019-09-10 21:01:21

Greg Kourakos
2019-09-10 21:21:59

Greg Kourakos
2019-09-10 21:22:24

Nick Hough
2019-09-10 22:58:53

Greg Kourakos
2019-09-10 23:01:16

Sean Croteau
2019-09-14 09:11:21

Sean Croteau
2019-09-14 15:40:50

Nick Hough
2019-09-14 19:18:18

原文網址 James Byberg
2019-09-10 12:09:23

Looks like second time is the charm. Must have had the plate too high, but I'll recheck it in the morning. Thanks for the advice and tips!

翻譯年糕

Justin Olsen
2019-09-10 12:11:08

James Byberg
2019-09-10 12:16:01

原文網址 Mitchell Smith
2019-09-10 12:00:48

Stoked about a project I'm working on. I have a flashlight that I love and but it is not durable when it comes to falls. I have designed a die to over mold the front and back with.....I dont know yet. Didnt know if any of you guys had experience with something like overmolding and what will hold up and last. Plan on printing on the photon.

翻譯年糕

原文網址 Plamen Penev
2019-09-10 11:31:19

These things are printed in BlueCast Crea at 50 um 14 sec. They are 4 cm in diameter, supported in Meshmixer, fixed in PhotonFileValidator. Good fine detail overall, but there are issues with keeping circular shape - the solid ones are slightly elongated while the filigree ones are almost correct. Probably there are not enough supports to keep the shape of the solid ones fixed, I don't know... Any idea, please?

翻譯年糕