Anycubic Photon Printer Owners 造訪社團

原文網址 Lorin Flemming
2019-09-07 08:22:22

Hi, can't find my Photon Thumb Drive. :( . Anyone know where I can download the sliced cube test file?

翻譯年糕

Jean-François Meloche
2019-09-07 08:27:19

Lorin Flemming
2019-09-07 09:24:07

原文網址 Paolo Angelo Bonafe
2019-09-07 08:17:34

原文網址 Brett VanDyke
2019-09-07 08:15:49

Is the twisting on the end of this print because I forgot to make it hollow?

翻譯年糕

Ethan Brown
2019-09-07 08:18:20

Brett VanDyke
2019-09-07 08:21:53

Ethan Brown
2019-09-07 08:24:22

原文網址 Chris Cassaday
2019-09-07 07:59:18

Anyone use “floating table” or rubberized feet for reducing vibration into the printer? My shop is up on cinder blocks so I’m concerned about inducing vibration when opening or closing doors or walking around. I’ve got rubberized floor mats on the ground and probably will put a rubber mat under the printer. I’m wondering if the fidelity of this printer that vibration might be an issue.

翻譯年糕

Nathaniel Red Weidner
2019-09-07 08:03:14

Joel Reid
2019-09-07 08:03:23

Chris Cassaday
2019-09-07 08:05:23

Joel Reid
2019-09-07 08:06:02

Sean Croteau
2019-09-07 23:13:53

Ric Watts
2019-09-08 04:00:51

原文網址 John Berger
2019-09-07 07:53:47

Well -- wish me luck :)

翻譯年糕

Handrez Pintubola
2019-09-07 08:01:11

Brett VanDyke
2019-09-07 08:04:07

Kasper Kolsrud
2019-09-07 08:14:44

Jesse DeGraff
2019-09-07 08:30:12

John Berger
2019-09-07 08:36:19

Doug Clark
2019-09-07 08:42:28

Tony Hutson
2019-09-07 10:47:49

Ben Lord
2019-09-07 10:53:17

Kris Jiles
2019-09-07 14:58:54

Lena Marilyn
2019-09-07 16:07:04

Tony Hutson
2019-09-07 21:25:30

Kris Jiles
2019-09-07 21:26:38

Tony Hutson
2019-09-07 21:49:02

John Berger
2019-09-08 00:51:53

Tony Hutson
2019-09-08 01:34:37

原文網址 Philippe Maegerman
2019-09-07 07:22:21

Qilin, the guardian lion @ .03 resin phrozen gray hollowed in meshmixer, 2mm thickness, 3mm holes running epax firmware for a few prints now, it's doing great
https://cults3d.com/en/3d-model/art/guardian-lion-or-foo-dogs-3d-model 翻譯年糕

Moisés Arturo Clemente
2019-09-07 08:30:03

Philippe Maegerman
2019-09-07 16:46:43

Philippe Maegerman
2019-09-07 16:47:20

Alexius Lim
2019-09-07 19:22:15

Lorenzo Castolo Melizza
2019-09-07 22:55:32

Mark Wardle
2019-09-07 23:10:23

Philippe Maegerman
2019-09-08 00:40:49

Antonio Robbins
2019-09-08 04:18:56

Philippe Maegerman
2019-09-08 04:47:40

原文網址 Matt Leese
2019-09-07 07:20:25

Ok, since I found myself with a little spare $, I decided to order a spare screen from the Anycubic Ebay store. Is it ready to install out of the box?

翻譯年糕

George Bulte
2019-09-07 07:31:14

Matt Leese
2019-09-07 07:35:19

Jaco Norchie Nortje
2019-09-07 07:42:59

Matt Leese
2019-09-07 07:58:57

原文網址 Davoud Taghawi-Nejad
2019-09-07 06:31:54

Z-Suite can now be used with the photon (instead of Chichubox) Did anybody use it? What results?

翻譯年糕

原文網址 Moss Eon Downs
2019-09-07 06:14:58

Hi,
Been lurking and trying to figure this out myself but I'm getting frustrated so figured id ask hive mind before I end up losing my ? Chitubox (tried photon slicer, same results)
.03 layer @ 8 sec exp, 6 bottom @ 50 sec
33° angle (as per that image that always gets posted here).
Tried it in all sorts of angles and exposures and i always get these lines that look horrid and are quite obvious.

Any help would be appreciated greatly
Is there a chance that my crappy laptop is stuffing up the slicing process? Can't post a pic of chitubox atm but can when I'm home later if needed
Edit: monocure rapid clear resin

翻譯年糕

John Oomen
2019-09-07 06:34:47

John Oomen
2019-09-07 06:35:14

Moss Eon Downs
2019-09-07 06:37:12

Fred Bey
2019-09-07 07:10:07

Moss Eon Downs
2019-09-07 07:57:31

John Oomen
2019-09-07 08:02:05

Moss Eon Downs
2019-09-07 08:10:54

Moss Eon Downs
2019-09-07 08:16:09

John Oomen
2019-09-07 08:16:23

Moss Eon Downs
2019-09-07 08:19:28

John Oomen
2019-09-07 08:21:53

原文網址 Shane Johnson
2019-09-07 06:12:58

Does anybody know of a measure file I can add to chitubox and see the mm of the items I've added? It would be awesome to have one that measures each side and height.

翻譯年糕

Che Fielding
2019-09-07 06:19:18