Anycubic Photon Printer Owners 造訪社團

原文網址 Kory Sebby
2019-06-12 23:01:02

The plasitc scraper i got with my phonton finally died. Can i use a plastic putty knife on the FEP to remove cured resin or am i stuck emptying the vat and using IPA?

翻譯年糕

Bob Deblier
2019-06-12 23:12:41

Matt Leese
2019-06-12 23:13:11

Kory Sebby
2019-06-12 23:13:27

Kory Sebby
2019-06-12 23:14:24

Gabriel Boswell
2019-06-12 23:14:29

Bob Deblier
2019-06-12 23:15:23

Kory Sebby
2019-06-12 23:16:15

Ben Cox
2019-06-14 04:18:24

原文網址 Israel Perez
2019-06-12 22:27:07

Ok so this is a weird problem i keep having. Ive used up a lot of resin trying to sort it out. Either the front of the print doesn't stick to the plate or it starts to tilt up and gets really thick. Its starts out levelled and all the screws are as tight as i can make them. You can see from one slicer what its meant to print out like... I don't know why this keeps happening at the front of the print. I suspect its the suction but if i dont make the level tight it wont stick at all. Im stuck and dont want to waste anymore resin

翻譯年糕

Brian Harrison
2019-06-12 22:33:10

Chad Elstad
2019-06-12 22:33:42

Brian Harrison
2019-06-12 22:33:51

CJ Hamilton
2019-06-12 22:34:36

Brian Harrison
2019-06-12 22:35:33

Sam Cunningham
2019-06-12 22:37:18

CJ Hamilton
2019-06-12 22:38:25

Dennis Back
2019-06-12 22:44:56

Israel Perez
2019-06-12 22:48:16

Israel Perez
2019-06-12 22:49:51

Andrea Brivio
2019-06-12 22:51:13

Andrea Brivio
2019-06-12 22:51:46

Israel Perez
2019-06-12 22:56:31

Andrea Brivio
2019-06-12 22:57:42

Mike Ratcliffe
2019-06-12 23:46:06

Mike Ratcliffe
2019-06-12 23:48:06

Kyle Urban
2019-06-13 03:32:07

Mike Ratcliffe
2019-06-13 03:34:20

Mark Wardle
2019-06-13 03:57:45

Stephen Farrell
2019-06-13 06:02:42

Kljunaš Avstralski
2019-06-13 14:59:31

原文網址 Alex Hines
2019-06-12 21:58:10

Can anyone recommend a good clear resin that will not discolour too much that can take dyes well? Seen a load that seem to print really yellow.

翻譯年糕

Ben Cox
2019-06-14 07:40:17

Alex Hines
2019-06-14 14:49:23

原文網址 Giulio Galassi
2019-06-12 21:38:25

First print with supports in chitubox, lower supports are 0,45 contact area and upper are 0,35 sphere contact form, i think i've to increase...

翻譯年糕

Giulio Galassi
2019-06-12 23:55:39

原文網址 Chayanin Somton
2019-06-12 21:37:00

whoa okay.... so this is my first print with the new bottle of Anycubic Grey that I just got, it was a blue-ish grey at first but some parts turned yellow-y grey and it looks pretty blotchy(kinda obvious in the 2nd pic) I think it was post-cure process that yellowed the resin as the areas that turned yellowed are where the UV light hits the most even though I only cure my parts for 3 minutes on each side(the UV lamp is on the top in the UV chamber)Has this happened to anyone that use Anycubic Grey? IDK I don't mind the slight color change i'm just a bit curious.

L to R: before post-cure, post-cure, post-cure

翻譯年糕

Oriol Fernandez
2019-06-12 22:23:25

Chayanin Somton
2019-06-12 22:24:09

Oriol Fernandez
2019-06-12 22:25:10

Chayanin Somton
2019-06-12 22:37:31

Chayanin Somton
2019-06-12 22:38:22

Chayanin Somton
2019-06-12 22:40:23

Lane Shutt
2019-06-13 05:13:47

Peter Ede
2019-06-14 16:44:00

Peter Ede
2019-06-14 16:45:54

Oriol Fernandez
2019-06-14 19:07:51

原文網址 Ian Golden Krasser
2019-06-12 21:28:53

原文網址 Paul Ciao
2019-06-12 20:44:01

Other than firmware, what other slicer can do horizontal compensation? Files that I've been printing have a bit of difficulty in terms of fitting together

翻譯年糕

原文網址 Mike Rooke
2019-06-12 20:36:19