Anycubic Photon Printer Owners 造訪社團

原文網址 Ciprian Parconie
2019-04-22 05:02:37

from what i have tested, i saw that after the post uv cure, tiny models like jewelry(rings/earnings/etc) become more breakable/ brickle . And until than are a little bit more elastic
Do you guys have prints that you don`t put in UV cure after the print? What`s the long term effect?
Thank you

翻譯年糕

Hector Felix
2019-04-22 05:09:31

Ciprian Parconie
2019-04-22 05:10:21

Joel Dawson
2019-04-22 05:16:50

Ciprian Parconie
2019-04-22 05:17:59

Hector Felix
2019-04-22 05:18:24

Stefan Giudici
2019-04-22 06:49:20

原文網址 Michael Muir
2019-04-22 04:51:56

Siraya Blu has been working pretty well with the heater installed, really impressed with how tough this resin is, this will be my go to resin at least for end use parts

翻譯年糕

Steven Sorton
2019-04-22 04:55:42

Michael Muir
2019-04-22 05:05:02

Mike Tree
2019-04-22 05:35:00

Michael Muir
2019-04-22 06:20:56

原文網址 Steven Parrish
2019-04-22 04:40:34

Has anyone uploaded their settings, including support settings, for Chitubox yet?

翻譯年糕

原文網址 Ali Daneshgar
2019-04-22 04:13:30

Sculpted it in zbrush( the 2D concept is by Chris Ayers)
Printed it in 3 pieces with anycubic.
Not sure why but the pieces didn't match well. So I used Dremel a lil bit. I should say my craftsmanship sucks big time.

翻譯年糕

Arminas Didziokas
2019-04-22 04:31:19

原文網址 Richard Thomas
2019-04-22 03:50:09

What flexible resin are those in the UK using?

翻譯年糕

Richard Thomas
2019-04-24 17:11:55

David Blewitt
2019-04-24 18:09:20

Richard Thomas
2019-04-24 19:33:16

Richard Burrell
2019-04-24 19:37:45

Richard Thomas
2019-04-24 19:39:22

Richard Burrell
2019-04-24 19:43:53

Richard Burrell
2019-04-24 19:44:50

原文網址 Paul Youdelis
2019-04-22 03:12:15

I said I would post a better pic today, so here it is....

翻譯年糕

原文網址 Leonardo Delgado
2019-04-22 03:11:27

Validator just shows "complete" and wont show total layers and doesnt seem to be checking the integrity of the file and islands..

Doesnt happen with all the files, just this one im trying to check. Tried re-slicing it and still same result, doesnt happen if i slice with Nardj Open Slicer, just Chitubox 1.4.

翻譯年糕

Bob Deblier
2019-04-22 03:23:56

Leonardo Delgado
2019-04-22 03:24:58

Bo Nørgaard
2019-04-22 04:15:37

Leonardo Delgado
2019-04-22 05:08:09

Leonardo Delgado
2019-04-22 09:01:31

Sen Kun
2019-04-22 13:45:22

Vinicius Silva
2019-04-22 18:12:45

Bo Nørgaard
2019-04-22 18:32:05

Leonardo Delgado
2019-04-22 18:33:17

Leonardo Delgado
2019-04-22 18:38:23

Sen Kun
2019-04-24 00:47:44

Michael McElrath
2019-04-24 01:08:19

Bob Deblier
2019-04-24 02:11:22

Leonardo Delgado
2019-04-24 02:21:14

Leonardo Delgado
2019-05-07 02:41:36

Sen Kun
2019-05-07 02:57:54

Leonardo Delgado
2019-05-07 05:57:42

原文網址 Jason Kelly
2019-04-22 03:10:53

I have recently seen more and more random flakes of cured resin attaching it self to my prints. Most recently when trying out eSun Standard resin I would get a huge mass of flakes. The pictures below show what happens when I try to print the Ameralabs test print.

I thought the FEP was finally dead, so I changed that. No improvement. I tried different settings and no change. I did notice that when I used Photocentric's firm UV resin the flakes would be smaller. So my question is this, is it possible the LCD screen is allowing light to pass though the areas it is suppose to be masking?

翻譯年糕

James Bricknell
2019-04-22 03:26:53

Robert Maefs
2019-04-22 07:22:57

Mark Wardle
2019-04-22 07:57:57

Jason Kelly
2019-04-22 08:05:42

Sen Kun
2019-04-22 13:47:38

Nick Williams
2019-04-22 14:01:35

Nicholas Hughes
2019-04-22 15:45:40

Jason Kelly
2019-04-22 19:33:39

Nick Williams
2019-04-22 23:37:42

Jason Kelly
2019-04-22 23:39:47

Nicholas Hughes
2019-04-23 00:21:54

Muhammad Zulkhairol Yacob
2019-04-24 21:39:05

原文網址 Michael Thomas
2019-04-22 02:37:23

So I have been using the Photon File Validator! Good thing. It appears that when I try to save a file that I created the supports for as an STL then bring back to combine with other files in Photon Slicer the software raises the object .1 mm off of the build plate. I was getting 2 uncured layers and would not have known it. Check out Nick Williams video. It will save you.

翻譯年糕

David Nicholls
2019-04-22 02:54:07

Michael Thomas
2019-04-22 03:04:38

Nick Williams
2019-04-22 03:07:04

Michael Thomas
2019-04-22 03:29:23

原文網址 Richard Thomas
2019-04-22 02:23:56

Couldn't resist trying this in the Anycubic Maroon and like the results.

翻譯年糕

討論主題

發文排行榜

回文排行榜

熱門關鍵字