Anycubic Photon Printer Owners 造訪社團

原文網址 Sam Charles Chaperz
2019-03-30 21:39:16

Has any one ever added things to the resin like glitter?

原文網址 Andrew Chan
2019-03-30 21:27:21

Honestly it looks and feel pretty solid and I don’t have any difficulty opening the front door (as complained in that “garbage” youtube review). The plastic case isn’t structural and is detached from the rails, it’s only an enclosure. I don’t think it’s filmsy either because of the flexibility of the material.

翻譯年糕

Simon Söderberg
2019-03-30 21:36:49

Mike Eckert
2019-03-30 21:44:59

Andrew Chan
2019-03-30 22:46:03

Ocie Ward
2019-03-30 23:06:28

Ocie Ward
2019-03-30 23:09:48

Sebastian Fernandez
2019-03-30 23:41:24

Andrew Chan
2019-03-31 00:01:48

Jadean Lazulli
2019-03-31 00:41:24

Richard James Sanchez
2019-03-31 02:17:20

Sen Kun
2019-03-31 02:20:34

Rod Shumway
2019-03-31 05:02:38

Andrew Chan
2019-03-31 05:33:15

Jadean Lazulli
2019-03-31 05:34:03

Don Roberts
2019-03-31 08:22:55

Don Roberts
2019-03-31 09:19:56

Jonathan Hall
2019-03-31 13:06:39

Francisco Hernandez
2019-03-31 16:18:46

Jadean Lazulli
2019-04-01 00:43:13

原文網址 Jason Croft
2019-03-30 21:06:29

Ok, I may have just learnt a harsh lesson. My last print did not print...

So I decide after 7 days now is the time to change my FEP, more then anything clean inside and see how it's done. Ok screws...lots of screws...seems a lot easier then I anticipated watched a video...finish and sucess

How ever there was what looked like a "smear" on the FEP and since the rest was like crystal I decide to wipe it with a paper towel..."oh no" I think it's smeared I'll give it a gentle rub and clear it up...

It's covered in what looks like tiny scratches how bad is this going to be as it is new and they are almost "cloudly" in appearence more then actual scratches ?

翻譯年糕

Yves Hacault
2019-03-30 21:13:35

Ed Wilson
2019-03-30 21:15:20

Jason Croft
2019-03-30 21:45:22

Jason Croft
2019-03-30 21:46:07

Rob Jansen
2019-03-30 22:14:20

Jason Croft
2019-03-30 22:17:36

Rob Jansen
2019-03-30 22:19:18

Sen Kun
2019-03-30 22:21:35

Sen Kun
2019-03-30 22:23:45

Jason Croft
2019-03-30 22:28:39

André Pereira Simões
2019-03-30 22:32:29

Jason Croft
2019-03-30 22:34:01

Jehú Paulín
2019-03-30 22:50:59

Jason Croft
2019-03-31 01:42:26

Rob Jansen
2019-03-31 02:12:14

原文網址 Keith Hebard
2019-03-30 20:11:17

Quick question, does anyone know if you have to set z zero again after a firmware upgrade or is that left untouched by the upgrade?

翻譯年糕

Marvel Mendoza
2019-03-30 20:23:02

Keith Hebard
2019-03-30 20:26:27

Paul Churchill
2019-03-31 07:42:41

原文網址 Andreas Jansson
2019-03-30 20:10:57

what fans did you replace the original ones with? So f*king loud!
original photon, not S version

翻譯年糕

Devin Wallace Simonsen
2019-03-30 20:23:25

Andreas Jansson
2019-03-30 20:24:04

Andreas Jansson
2019-03-30 20:24:22

Chad Elstad
2019-03-30 20:59:52

Devin Wallace Simonsen
2019-03-30 21:00:59

Andreas Jansson
2019-03-30 21:01:31

Chad Elstad
2019-03-30 21:31:13

Andreas Jansson
2019-03-30 21:31:51

Björn Ståhlnacke
2019-03-30 22:06:55

Andreas Jansson
2019-03-30 22:26:19

原文網址 Sam Charles Chaperz
2019-03-30 20:03:44

What would cause these virticle lines going opposite way to the layers

翻譯年糕

Mark Simpkins
2019-03-30 20:14:05

Sam Charles Chaperz
2019-03-30 20:15:46

Ryan Gamble
2019-03-30 20:19:05

Sam Charles Chaperz
2019-03-30 20:33:34

Ryan Gamble
2019-03-30 20:39:41

Sen Kun
2019-03-30 20:51:35

Ryan Gamble
2019-03-30 20:52:58

Sen Kun
2019-03-30 20:56:14

Vinicius Silva
2019-03-30 21:03:26

Vinicius Silva
2019-03-30 21:04:33

Vinicius Silva
2019-03-30 21:05:50

Ryan Gamble
2019-03-30 21:07:37

原文網址 Erik Mendelsohn
2019-03-30 20:01:16

My photon stopped moving up the z-axis. Any clue what would case this. It happens on every print, I tried reboot. If I move the z-axis during homing there are no issues going up or down. I tried the firmware. Any ideas?

翻譯年糕

Jarrod Smith
2019-03-30 20:24:26