Anycubic Photon Printer Owners 造訪社團

原文網址 Rick Graham
2018-05-04 08:37:44

Hey everyone, so I am trying to print some tokens but I am really running into problems. I am attempting to print 12 tokens but only the middle row is sticking on the supports. The four however are also coming out warped and not flat as they were designed. I have attempted this twice thinking there was a problem the first go around.

I have cleaned the vat, but it still keeps happening. Any clues?

翻譯年糕

原文網址 Jay Gustavo Mclean
2018-05-04 08:10:54

all 3 stages big thanks to Gregory Crouch for printing Ferrovax

翻譯年糕

原文網址 Chad Elstad
2018-05-04 07:56:36

Do folks let their Photon printers run while no one is around? What precautions do you take, if any. Please add a comment for precautions.

翻譯年糕

原文網址 Chad Elstad
2018-05-04 07:25:58

Hmm, what could be happening here? The leg didn't print on this one, but the same file printed only both legs and supports with an 11 vs 12 exposure setting.

翻譯年糕

原文網址 Lucas Zacharias
2018-05-04 07:17:21

So i've been trying to have a successful print on my new machine but i just can't get the part to stick to the build plate. I've readjusted the Z axis multiple times to no avail. Not sure what else to do at this point... Anyone have any advice on the matter? Also how do I clean all the resin off the build plate after a print? I'm worried that half dried resin on the bottom could be an issue...

翻譯年糕

原文網址 Phil Davidson
2018-05-04 06:32:12

Last night I found some free prints on the http://www.monocure3d.com.au/category-s/181.htm website

If you click through there are some amazing prints to download for free - e.g. here's a pic of one available from Duncan

翻譯年糕

Jay Gustavo Mclean
2018-05-04 06:37:33

CK Barzin
2018-05-04 06:41:38

Phil Davidson
2018-05-04 07:41:06

Mark Wardle
2018-05-04 08:08:16

Phil Davidson
2018-05-04 08:10:26

Mark Wardle
2018-05-04 08:12:11

原文網址 Chris Marshall
2018-05-04 05:50:34

Hello all. Just got my Photon in yesterday. Got it setup and going with an initial print. It only did the raft and I had to scrape it off of the resin tank. Tried again this morning before work, same result. Only the raft and stuck to the bottom of the tank. What did I miss?

翻譯年糕

原文網址 Mirko Crispoldi
2018-05-04 05:23:43

Update about my 6cm Ornstein from Dark Souls:

翻譯年糕

原文網址 Ryan Thomas Kamakea Aubin
2018-05-04 04:59:21

So here's a question... Does anyone know how big each square is supposed to represent on the Anycubic Slicer? Can we somehow resize the grid to better orient the size of the prints?

翻譯年糕

原文網址 Kyle Standring
2018-05-04 04:56:36

Hey all! Got my Photon yesterday! Lattice Cube test print went perfectly! Want to try a couple more proven Photon files before stating to make my own supports etc. does anyone have a link to the Baby Groot model already with supports etc. Just want to make sure the printer is dialed in before I make my own stuff, that way I know any failures are on my end and not machine calibration, thanks!!

翻譯年糕