Anycubic Photon Printer Owners 造訪社團

原文網址 Katie Farrant
2020-01-12 19:41:21

After an initial failed print here is my 1st successful print on my photon. The lute on her back misprinted slightly but I’m stoked with the quality.

翻譯年糕

原文網址 Peter Kovacs
2020-01-12 19:38:15

Hey all. Does someone knows what material has similar properties to Games Workshops grey plastic miniatures? Is it possible to print a material like that with a photon or photon s?

翻譯年糕

Amy Baldwin
2020-01-12 20:01:46

Amy Baldwin
2020-01-12 20:02:21

Markus Jorissen
2020-01-12 20:03:47

Joey Smith
2020-01-12 21:37:01

Jlee Usn
2020-01-12 23:33:29

Jlee Usn
2020-01-12 23:34:43

Grégou Johnsonne
2020-01-13 03:05:01

Peter Kovacs
2020-01-13 04:31:53

Peter Kovacs
2020-01-13 04:33:30

Peter Kovacs
2020-01-13 04:35:22

Chris Holden
2020-01-13 04:49:35

Jlee Usn
2020-01-13 10:10:53

Peter Kovacs
2020-01-14 17:33:06

Chris Holden
2020-01-14 23:24:43

原文網址 Paul Beards
2020-01-12 19:25:49

Morning all. Just a quick question - I have just bought some Epax non-fep for my Photon, and just wondered if this usually comes with protective film to peel off, or not?

It's not obvious if it does, so before I fit, just wanted to make sure.

翻譯年糕

原文網址 Zbigniew Perski
2020-01-12 19:16:56

Hi, most of you are printing SF and fantasy figures. I am looking for some civilians (modern and historical) for diorama purposes. Could anybody here can recommend a site where can I find them?

翻譯年糕

原文網址 Hein Htet Aung
2020-01-12 18:56:13

For a customer as he couldn't find any replacement for his zipper head. Printed on Photon S.

翻譯年糕

David Collinson
2020-01-12 19:23:46

Hein Htet Aung
2020-01-12 19:32:16

João Tomás Afonso
2020-01-12 20:19:57

Scott Dimmick
2020-01-12 21:48:38

João Tomás Afonso
2020-01-12 22:27:41

Hein Htet Aung
2020-01-13 00:31:11

Ernie Gee
2020-01-13 06:22:22

Hein Htet Aung
2020-01-13 10:00:38

Ernie Gee
2020-01-13 10:05:15

原文網址 Alex Nadalini
2020-01-12 18:49:59

Hi All,

Bought a Photon just before Christmas and I'm hoping to get a little help with a minor issue I have with a test print I just finished earlier today, I used chitubox and cloned the item, printed one flat to the build plate and the other angled using (auto)supports, when I looked at the prints they both have a slight bow, I'm using Anycubic blue resin and I've got the layer height at 0.05, 10 bottom layers for 80 secs & the remainder @ 8 secs, once the print finished I used "Methylated Spirits" to wash the models, dried and put them outside to 'cure' (overcast day) for about 15 mins. - its about 25 * 50 *3mm and has a slight (unintentional) bow along the length, help... - ohh also I shook the resin bottle (as advised) and can see what appears to be squashed bubbles where the prints would have been against the build plate - not sure it thats normal or not

翻譯年糕

Karoten Buford
2020-01-12 23:16:41

Alex Nadalini
2020-01-13 06:14:44

Karoten Buford
2020-01-13 06:20:56

Alex Nadalini
2020-01-13 06:22:40

Karoten Buford
2020-01-13 06:30:18

原文網址 Kostas Yiatilis MacFarlane
2020-01-12 18:20:41

Cute little tentacled thingies

翻譯年糕

Sander van Deijl
2020-01-12 18:23:17

Mikel Deiman
2020-01-12 18:39:48

Kostas Yiatilis MacFarlane
2020-01-12 18:40:10

Jade Axline
2020-01-13 01:31:35

Evan Rosario
2020-01-13 02:28:13

Kostas Yiatilis MacFarlane
2020-01-13 03:52:31

Kostas Yiatilis MacFarlane
2020-01-13 03:52:34

Kostas Yiatilis MacFarlane
2020-01-13 03:52:40

Benjamin Mitchell
2020-01-13 05:38:04

Kostas Yiatilis MacFarlane
2020-01-14 18:05:00

原文網址 James Mullin
2020-01-12 18:10:39

So had a failure again .. no biggie it's a learning curve .. I picked out the piece that printed and didn't stick to the printing bed from the vat .. do I need to re drain the resin and clean the vat and pour more in .. it's only been sitting a few hours or can I use it as is ??? I made adjustments from ideas from here and utube

翻譯年糕

Matt Hooton
2020-01-12 18:16:43

James Mullin
2020-01-12 18:18:51

James Mullin
2020-01-12 18:21:07

TJ Strickland
2020-01-12 19:38:43

原文網址 Matthew Steeghs
2020-01-12 17:53:52

Need some help again guys having issues.

Talking with anycubic but they are just referring me to the youtube videos they have.

I have check Z wobble and there is none machine is level. Z zero is really good

Print settings are

Layer height 0.03mm
Bottom layers 5 exposure 95sec
Standard exposure 10sec
Off time 3 sec
Lift retract 6mm

I'm having a real issue with the supports having this wobble In it and in turn of it being in my supports it is going through my print since i print on a twin axis angle. Any help would be amazing as I'm almost tempted to ask for a refund.

翻譯年糕