ATOM 3D Printer Group 造訪社團

原文網址 KioSky Chung
2016-08-25 23:23:37

［求問］

最近印一些大件物品時
尾段突然接不起來，整個就變成失敗的麵球，請問是什麼原因呢⋯⋯ （溫度190 PLA )

戴士偉
2016-08-25 23:24:09

出料不順...

Charlie Ting
2016-08-25 23:25:31

同意樓上

Clarence Lee
2016-08-25 23:26:19

可以考慮檢查擠出機構或是換個別種擠出機構用看看...

張建祺
2016-08-25 23:27:00

噴嘴散熱也會影響喔~~\

黃俊傑
2016-08-25 23:30:46

先看看後吹有無裝反？

KioSky Chung
2016-08-25 23:36:52

:0 感謝解惑。後吹沒裝反。擠出機構好像有點歪掉了

KioSky Chung
2016-08-25 23:38:53

掉很多屑屑

KioSky Chung
2016-08-25 23:40:47

後吹應該沒問題⋯⋯

梁啓修
2016-08-26 00:06:50

感覺很有型

廖新弘
2016-08-26 06:09:29

喉管的鐵氟龍管多久沒有換了

鄭鈞庭
2016-08-26 09:55:53

擠出機夾料太緊

原文網址 陳宛伶
2016-08-25 17:23:32

今天完成一個sample,但是有些問題要請各位大大幫忙解答......
附上照片同一件怎麼有些面會相對的完整.....

陳亮宇
2016-08-25 17:56:34

檢查看看擠出孔是不是有點歪掉?

MoMo Yang
2016-08-25 19:18:02

方便提供左邊那張圖檔嗎，我可以幫你測試

廖新弘
2016-08-25 20:29:54

參數貼出來吧

陳宛伶
2016-08-26 09:21:16

請各幫高手指點....

廖新弘
2016-08-26 10:12:04

ATOM的噴嘴尺寸是0.4

原文網址 Birk Binnard
2016-08-25 13:35:39

Craftware Manual (English only)

https://craftunique.com/docs/craftware-user-manual

This is an excellent manual that describes the Craftware slicer software. Craftware is my slicer of choice becuase it slices faster than any other slicer out there and has by far the best visualization capabilities I've seen. The current version is quite reliable and there is a version fo Mac computers too. And it is free.

翻譯年糕

原文網址 Dan Salvador
2016-08-25 12:30:04

How about that? PLA from Atom Printer to ceramic mold casting

翻譯年糕

原文網址 MoMo Yang
2016-08-25 12:21:27

ATOM真是讚呀

Dan Salvador
2016-08-25 12:25:09

Very beautiful job ?

張不凡
2016-08-25 13:12:05

偷偷問一下來源檔案是...

陳曉澔
2016-08-25 13:13:19

漂亮細緻。

許阿瑋
2016-08-25 13:44:05

這有點猛

Lu-ann Chen
2016-08-26 18:10:41

倒過來印的?還是支撐?

廖新弘
2016-08-26 22:50:40

http://www.thingiverse.com/thing:1100932

杨威
2016-08-29 10:09:03

啊是默认参数打印么？

原文網址 Willy Wu
2016-08-25 10:58:04

想請教一下各位
喉管內的鐵氟龍管尺寸是多少mm?
感恩~

梁琄
2016-08-25 11:03:19

2*3的，一號盒裡面有備用的20cm

Willy Wu
2016-08-25 11:11:58

那要剪多長呢?? 謝謝你~

原文網址 Birk Binnard
2016-08-25 01:19:15

VoronoiBowl2A

This is VoronoiBowl2's basic geometry, but with the ribs changed to circular cross sections. With this change I was able to eliminate all the sharp corners which resulted in a more organic look. Printing is still a challenge for prime/retract/stringing and bridging. This part printed in 26 1/4 hours @ 0.200 mm layer height.

Photo's 2 & 3 show some problems with the print. I'm not sure what caused these - it might be that the overall structure was not strong enough to hold the part 100% still while it was being printed.

The good news is that by changing prime/retract from 5 mm to 6 mm I was able to eliminate almost all stringing.

The STL file for this part is here:

http://www.thingiverse.com/thing:1734937

https://pinshape.com/items/25308-3d-printed-voronoibowl2a

翻譯年糕

原文網址 Morgan Chang
2016-08-24 22:57:20

前陣子很流行的鑰匙圈吊飾, 為了減輕口袋的負擔, 我重畫了縮小版 (36mm *12mm, 0.6mm間隙)
順便加上中心的5mm六角孔&側面3mm孔, 剛印好要分離各層時少花一點力氣, 尤其是最中心原本沒有施力點,有輕微沾黏就很難分離.
http://www.thingiverse.com/thing:1734678