hi there i have a few problem with my printer i think it's mechanical but i don't find it.. so if you have any idea thx
:)
翻譯年糕
Charlie Ting
2015-11-04 00:14:24
Check all screws on the hub.
李穆
2015-11-04 00:17:04
G29 Z+0.* <----- get * larger and try again
Jean Baptiste Léopold Trullu
2015-11-04 00:33:25
i try G29 Z+0.25; 0.3; 0.4; 0.5; 0.55 actual and 0.6 to far...
Jean Baptiste Léopold Trullu
2015-11-04 00:35:10
Jean Baptiste Léopold Trullu
2015-11-04 00:35:27
Jean Baptiste Léopold Trullu
2015-11-04 00:35:48
Jean Baptiste Léopold Trullu
2015-11-04 00:36:03
Jean Baptiste Léopold Trullu
2015-11-04 00:37:06
screws check nothing change...
Charlie Ting
2015-11-04 00:45:36
Then check tension of all timing belts and set Accel to 500~1000 from the LCD panel.
Set Z-lift to 0.5mm in your slicer program.
Jean Baptiste Léopold Trullu
2015-11-04 00:57:28
wow my Accel was set to 9000 (default value i supose?) !!... i try a print with Accel 1000 and 500 and i post result later thx charlie, we keep in touch
Jean Baptiste Léopold Trullu
2015-11-04 01:43:32
Accel 1000 on the left and 500 on the right.. 500 it's a little bit better but final result is the same.
Lawrence Lee
2015-11-04 16:27:15
do you have other prints? or could you share a screen shot of your slicer settings?
Jean Baptiste Léopold Trullu
2015-11-04 16:35:09
Hello, about news, I launched a file yesterday with new parameter Accel 500 and the progress its good, but there is gap by certain places..It come from tension belts?
Jean Baptiste Léopold Trullu
2015-11-04 16:36:15
Hi lawrence, some screen of mi slicer
Jean Baptiste Léopold Trullu
2015-11-04 16:36:24
Jean Baptiste Léopold Trullu
2015-11-04 16:36:32
Jean Baptiste Léopold Trullu
2015-11-04 16:36:40
Jean Baptiste Léopold Trullu
2015-11-04 16:37:40
Thank you for your efforts
Charlie Ting
2015-11-04 16:44:11
You may try these settings:
1. De-string trigger : 10mm
2. De-string Wipe : 0
3. Fan / Cool Min Layer : 3
4. Flow adjust Flow tweak : 1
5. Z-lift : 0.5mm
6. Temprature : 190
Lawrence Lee
2015-11-04 17:32:14
yup
Charlie
is right, the flow tweak stood out for me, excess filament might be causing the problem
Jean Baptiste Léopold Trullu
2015-11-04 17:52:08
OK I try that see you later thx
Jean Baptiste Léopold Trullu
2015-11-05 16:13:32
Hello, then it resulted is even better than on the previous printing, but it stays gap by place which deforms the object.
Charlie Ting
2015-11-05 16:26:49
How long have you used ATOM 2.0 printer?
The reasons I knew which caused gap between layers are two, PTFE tube or printer tolerant becomes worse.
Maybe you sholud check PTFE tube in the nozzle.
Jean Baptiste Léopold Trullu
2015-11-05 16:43:11
The machine has only some month, I don't use it a lot because I had its problem from the beginning. I also thought that the problem could possibly come from the tube.
Charlie Ting
2015-11-05 16:52:46
My last print yesterday.
After change ptfe tube, it got a smooth head. Before changed, its face is not so good.
Jean Baptiste Léopold Trullu
2015-11-05 17:15:20
ok then i try to change it...but do you have a ptfe tube stock because when you told that i have the feeling it's frequently the cause of the printer problem...?
Jean Baptiste Léopold Trullu
2015-11-05 18:02:51
Charlie Ting
2015-11-05 20:07:11
You may contact ALT design or purchase from eBay or taobao.
Charlie Ting
2015-11-05 20:07:28
Charlie Ting
2015-11-05 20:07:42
Jean Baptiste Léopold Trullu
2015-11-06 17:33:39
Okay I touch the purpose I believe. Thank you very much Charlie. I am going to continue of refined the regulations to take out the best print possible. I shall like trying the beta version 2.7 have you got some recommendation?
