ATOM 3D Printer Group 造訪社團

原文網址李穆
2015-10-04 22:07:14

[軟料試印生活小物] 修復錶帶及更換鍵帽
同樣的設定，開啟回抽就會出料遲滯，捉高溫度至215亦不見改善，因此關閉回抽重印，測試結果良好，僅以抹料處理，牽絲量亦可接受。
冷卻部份風扇全開，翹曲問題不明顯，對抗翹曲低溫+強風可以穩定取得好的成果。
下緣開啟支撐部份，跟列印件黏著性太好，拆除時易弄破列印件，建議以焊接烙鐵+刀頭進行移除，效果較好。

廖新弘
2015-10-04 22:10:59

佩服，我在思考要不要改回1.0版的擠料機構，上面加裝鐵弗龍管來試軟料

李穆
2015-10-04 22:22:27

ATOM提供測試的這支軟料可以用2.0的機構免改直上

廖新弘
2015-10-04 22:26:34

你們試的是廠商的吧，我考慮方向有點不同

Shi Xinhui
2015-10-05 22:34:36

給印實用小物一個大讚！！

原文網址 葉世瑋
2015-10-04 21:33:45

燒出來的感覺都差不多耶，這樣焦距是否就不用太在意了?

陳明谷
2015-10-04 21:37:19

9.4

Hawke ChienSheng Liu
2015-10-04 21:38:23

ATOM測試檔內容就是這個？

Charlie Ting
2015-10-04 21:43:41

可以換個材質看看，準焦的功率最大，效果最優。

李穆
2015-10-04 22:10:54

燒的時候紙應該不平吧？

葉世瑋
2015-10-05 11:44:31

這次換另一張紙並用口紅膠貼妥在平台上再燒一次，差別還是不大，所以就挑燒得比較穿的那組囉

原文網址 陳明谷
2015-10-04 19:24:01

http://inplus.tw/archives/1698

張不凡
2015-10-04 21:59:57

Mac 版還沒有更新，傷心

原文網址 Dan Salvador
2015-10-04 18:16:18

Dan Salvador
2015-10-05 01:32:41

I would have to wait for this 28 hour print to finish , then I will upload more pictures , I do appreciate you assistance, thank you so much

Dan Salvador
2015-10-05 01:37:02

Thanks

原文網址 Dan Salvador
2015-10-04 18:16:14

hi guys - can anyone assist why the first layer looks like that ?
2nd layer is ok

翻譯年糕

廖新弘
2015-10-04 18:27:59

廖新弘
2015-10-04 18:28:18

廖新弘
2015-10-04 18:28:33

廖新弘
2015-10-04 18:28:54

廖新弘
2015-10-04 18:29:08

廖新弘
2015-10-04 18:29:32

廖新弘
2015-10-04 18:30:05

廖新弘
2015-10-04 18:30:17

廖新弘
2015-10-04 18:30:32

曾荐宏
2015-10-04 18:51:09

廖大好神啊!!

廖新弘
2015-10-04 19:01:49

設定基本上跟KISSlicer一樣，部分再修改而已

廖新弘
2015-10-04 19:04:06

http://www.atom3dp.com/en/support/

Dan Salvador
2015-10-04 23:16:05

Thank you friend for the comments , I will try your comments , do you have problem with somplify3d VS auto leveling ?

廖新弘
2015-10-04 23:29:04

You can try it

廖新弘
2015-10-04 23:30:38

廖新弘
2015-10-04 23:35:39

Z offset?=G29 z+?

Dan Salvador
2015-10-04 23:45:56

Can you explain more deep ? Thank you so much for your assistance ? ?

Dan Salvador
2015-10-04 23:49:41

Also may I ask you kindly to send me your .FFF file to my email ? ( idan@plasteam.co.il )

呂嘉祥
2015-10-05 00:02:29

I think that it because your first layer is too thin.
maybe you should add the first layer's height.

呂嘉祥
2015-10-05 00:09:04

Oh, after I review the manual, maybe we should adjust the z-offset first. It will help ATOM to setup right first layer height.

廖新弘
2015-10-05 18:14:33

Dan Salvador
2015-10-06 01:01:07

Thank you all , tomorrow I will test it and let you know

吳普軒
2015-10-06 20:35:34

How is Simplify3D? It's very attractive, but a significant amount to devote. (even for their 2w trial) How is it compares to Cura and kisslicer?

Dan Salvador
2015-10-06 21:44:07

it is most comftarble and has many settings - you can see all my above screenshots of the setting - also the clice preview is greate and another thing is that you can add or remove support manually

Dan Salvador
2015-10-06 21:44:41

about my problem - it was simply a matter of Z offset (0.11) now all is ok

Dan Salvador
2015-10-06 21:45:48