• #maker+t=market
  • 3D列印服務
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Mario Hippmann
2020-03-27 05:31:33

the last prints i clean with IPA (with a brush) are extremly sticky after post curing,

anyone know why?

翻譯年糕

Dan Gump
2020-03-27 05:38:25

How are you cleaning the prints with an airbrush?

Mario Hippmann
2020-03-27 05:41:16

brush

Dan Gump
2020-03-27 05:44:04

so what is your process?

I do the following:

Remove from printer
Soak in 97% ISO for 5 minutes
Scrub with toothbrush, Rinse off
Put in Mean Green container #2
Soak for 10-15 minutes (or longer)
Fill bathroom sink with HOT water and rinse off model & remove supports
If still has sticky parts I repeat steps 1&2 and rinse again
Then let dry fully before curing

Mario Hippmann
2020-03-27 05:48:33

Dan Gump Remove from printer
take a big Brush soaked with IPA 99,9% and rinse off the most of the resin
remove from build plate (supports)
let is soak for some sec
rinse off with soaked Brush
change IPA (other container) with cleaner IPA
make the same again
dry it with a airblower (i think rinse it off with water atm will cause White color - IPA and water mixing)
post cure 15min

Jakub Mach
2020-03-27 05:53:49

What resin do you use?

Mario Hippmann
2020-03-27 05:55:08

Eleego Grey , used all time, since last 2 prints very sticky

Jakub Mach
2020-03-27 05:57:52

So you did not change absolutely anything and it wasn't sticky before?
Same resin, same postprocessing, same after-curing?

Scott Pavlich
2020-03-27 06:00:10

Cure them in water

Mario Hippmann
2020-03-27 06:00:53

Jakub Mach yes, also everything i touch in the post process is very sticky after that.... like the brush or the spatula (remove from buildplate)

Tyler Vins
2020-03-27 07:08:53

Replace your IPA

Panagiotis Kountouriotis
2020-03-27 07:47:14

Do not replace your IPA pour it in a transparent container and cure it with uv light over night, in the morning there will be solid residue in the container, filter out the solids and you can use it again and again

Mario Hippmann
2020-03-27 08:00:15

Panagiotis Kountouriotis i already filtered, IT was jelly, Not Solid

Paulo Duarte
2020-03-27 08:22:59

Make a post curing with a layer of any kind of transparent jelly , the exterior layer of the object cannot be fully polimerized due to the oxygen inhibit layer .

Panagiotis Kountouriotis
2020-03-27 08:25:00

I did it two days ago, when I do it again I will post some photos

Jeff Greenfield
2020-03-27 09:50:25

Call me crazy, but I swear my prints are sticky when the resin gets old. Maybe more of a constant temp would help prolong the life in the bottle, idk.

Mario Hippmann
2020-03-27 21:32:37

what? :D


原文網址 Mario Hippmann
2020-03-23 23:18:29

so i use Elegoostandart grey with 90S bottom and 11s normal.

now i bought a new bottle, can i still use 11s or do i have to print the calibration again?

翻譯年糕

Bob Deblier
2020-03-23 23:24:31

Do you feel lucky? Otherwise quickly print a calibration test ;)


原文網址 Mario Hippmann
2020-03-18 22:08:14

how much ml resin fit in the VAT, when i fill it to the "line"

翻譯年糕

Pete Frith
2020-03-18 22:12:35

Following ?

Warpy Pagan
2020-03-18 22:12:46

around 37ml if i remember correctly

Gregore Conn
2020-03-18 22:15:32

All of the resin. You ain't cool unless you post a pic with the resin damn near overflowing.

Mario Hippmann
2020-03-18 22:30:41

that way to less

Mario Hippmann
2020-03-18 22:30:58

?‍♀️ ?‍♀️

Terry Hobbs
2020-03-18 22:32:50

Up to the line is around 100 ml.

Nelson Tejada
2020-03-18 22:41:33

150 ml I think

Nelson Tejada
2020-03-18 22:45:46

Pour resin up to the line where the chamfer starts in the vat, about a quarter up from the FEP. This is about 125ml. From the Photonsters github

Cobey Schmidt
2020-03-18 22:53:16

125ml per spec

Jeremy Mongoose Harris
2020-03-18 23:10:10

It's better to not fill all the way. Resen gets into the screws and the ball joint. Gums up the works and needs a deep cleaning

Scott Pavlich
2020-03-18 23:59:17

150ml is a safe max

Artur Kawa
2020-03-19 01:11:24

Füll es sicherheitshalber mit Wasser auf und wiege es dann. 1 ml = 1 gramm. Wüsste ich es auch nicht genau aus dem Kopf.

Smith Hayward
2020-03-19 02:13:34

I love how so many people are guessing at something that is easily measured.

Aaron Strome
2020-03-19 03:35:53

when i measure out 100ml in a beaker it goes just barely over that line...

Mario Hippmann
2020-03-19 03:37:53

Aaron Strome dont make me weak, Just started a 9h Print 3 hours ago. IT needs 110ml. I am Not coming Home until 10 hours ?

Aaron Strome
2020-03-19 03:46:35

you have a lot of things to work out if you are judging my what chitubox say it weighs. is it hollow that adds a bit for trapped resin the surface resin that is left on it after the print and i always add 30ml more than chitubox says since it has been wrong many times before

Mario Hippmann
2020-03-19 03:49:41

Aaron Strome
2020-03-19 03:51:08

yeah unfortunately i think you're @#$%'ed sorry... unless you have someone who can add more resin or hit pause until you get home..

Mario Hippmann
2020-03-19 03:52:08

Aaron Strome my girlfriend is Not able to fill it . And Pause makes ugly Lines ?

Aaron Strome
2020-03-19 03:54:19

ugly lines versus a headless print.. hmmmm

Luiz Junior
2020-03-19 12:43:56

Mario Hippmann that’s because the temperature of the resin inside vat is higher than the one you are adding. So mixing them both will change resin temperature inside vat and also how much it’s expand when the layer is curing. If you are able to add some heat to the resin in the bottle, this effect should be less or none.

Mario Hippmann
2020-03-19 14:26:35

Aaron Strome yes i got fuc*** ? Just s little Bit was Missing

Mario Hippmann
2020-03-19 14:28:17

Luiz Junior rly? Thats the reason for the Lines ? I would have a Heat blower, but now its to late ?

Aaron Strome
2020-03-19 14:29:36

Luiz Junior
2020-03-19 22:08:55

Mario Hippmann you can pause and resume without add more resin and check that the lines won’t appear, only if you add cold resin to it. I’m thinking on a way to heat it easy...


原文網址 Mario Hippmann
2020-03-16 05:32:57

so i am about to buy models from gambody

but i worry, that the pieces wont fit because of SLA printing.

someone has experience?

翻譯年糕

John Yip
2020-03-16 05:39:19

Mario Hippmann
2020-03-16 05:40:32

Jim Carswell
2020-03-16 05:44:49

John Yip
2020-03-16 05:47:47

Mario Hippmann
2020-03-16 05:52:07

Jim Nelson
2020-03-16 05:54:51

Mario Hippmann
2020-03-16 07:39:36

Aaron Strome
2020-03-16 08:59:03

Mario Hippmann
2020-03-16 16:52:24

Aaron Strome
2020-03-16 16:55:11

Mario Hippmann
2020-03-16 17:01:25

Aaron Strome
2020-03-16 17:04:33

Aaron Strome
2020-03-16 17:05:12

Mario Hippmann
2020-03-16 17:21:42

Aaron Strome
2020-03-16 17:22:55

Aaron Strome
2020-03-16 17:24:16

Mario Hippmann
2020-03-16 17:28:58

Aaron Strome
2020-03-16 17:30:44

Aaron Strome
2020-03-16 17:31:20

Mario Hippmann
2020-03-16 17:31:51

Aaron Strome
2020-03-16 17:32:50

Aaron Strome
2020-03-16 17:34:03

Mario Hippmann
2020-03-16 17:34:41

Aaron Strome
2020-03-16 17:35:15

Mario Hippmann
2020-03-16 17:35:59

Aaron Strome
2020-03-16 17:37:47

Mario Hippmann
2020-03-16 17:39:26

Aaron Strome
2020-03-16 17:40:30

Aaron Strome
2020-03-16 17:41:11

Aaron Strome
2020-03-16 17:42:21

Mario Hippmann
2020-03-16 17:44:02

Aaron Strome
2020-03-16 17:46:22

Mario Hippmann
2020-03-16 17:46:34

Aaron Strome
2020-03-16 17:47:34

Mario Hippmann
2020-03-16 17:50:15

Aaron Strome
2020-03-16 17:50:58

Aaron Strome
2020-03-16 18:47:45

Mario Hippmann
2020-03-16 18:52:45

Aaron Strome
2020-03-16 18:53:54

Aaron Strome
2020-03-16 18:54:56

Mario Hippmann
2020-03-16 18:55:03

Aaron Strome
2020-03-16 18:56:01

Aaron Strome
2020-03-16 18:57:38

Mario Hippmann
2020-03-16 18:59:07

Aaron Strome
2020-03-16 19:01:36


原文網址 Mario Hippmann
2020-03-08 21:26:50

Does someone have DIY heater for photon? How its the easiest and cheapest Methode to do it?

翻譯年糕

Gregory Akin
2020-03-08 21:33:50

Jens Cole
2020-03-08 21:42:24

Vinicius Silva
2020-03-08 21:43:46


原文網址 Mario Hippmann
2020-03-06 19:45:01

Just something i wanna share.

this is a fu**ing good idea:

翻譯年糕


原文網址 Mario Hippmann
2020-03-05 22:19:44

So my Print comes Out perfect, exept this elbow. Why IT doesnt Print Well? Have Tried 2 Times (Changes some Supports there)

所以我的指紋出來了完美, 把這個肘放出來. 為什麼印刷不好? 嘗試過2次(有些支援)

· 查看原文 · 為此翻譯評分

Arthur White
2020-03-06 01:33:22


原文網址 Mario Hippmann
2020-03-05 06:41:35

Hello

Is this Support possible in chitubox?

翻譯年糕

Daniel Faubert
2020-03-05 06:43:04

Mario Hippmann
2020-03-05 06:43:51

Mike Dyer
2020-03-05 06:46:11

Mike Dyer
2020-03-05 06:46:32

Daniel Faubert
2020-03-05 06:46:32

Adam Bishop
2020-03-05 06:46:34

Adam Bishop
2020-03-05 06:47:12

Mario Hippmann
2020-03-05 06:48:00

Brandon Ray
2020-03-05 06:50:03

Yessik Ziiq
2020-03-05 06:52:12

Adam Bishop
2020-03-05 06:53:16

Adam Bishop
2020-03-05 06:54:25

Charley Dill
2020-03-05 07:15:15

Mario Hippmann
2020-03-05 07:33:01

Charley Dill
2020-03-05 07:41:47

Mario Hippmann
2020-03-05 07:48:18

Charley Dill
2020-03-05 07:51:08

Mario Hippmann
2020-03-05 07:57:32

Mark Wardle
2020-03-05 09:21:27

Jarrod Smith
2020-03-05 09:38:25

Mario Hippmann
2020-03-05 16:37:00


原文網址 Mario Hippmann
2020-03-03 21:58:33

What would U Guys say?

Elegoo Standart Grey 0,05mm

8s?

翻譯年糕

Bob Deblier
2020-03-03 22:03:54

Michael Grace
2020-03-03 22:10:07

Mario Hippmann
2020-03-03 22:13:29

Bob Deblier
2020-03-03 22:15:34

Mario Hippmann
2020-03-03 22:17:28

Bob Deblier
2020-03-03 22:19:19

Paul Soucy
2020-03-03 22:51:34

Mario Hippmann
2020-03-03 22:57:55

Balint Beni
2020-03-03 23:12:29

Mario Hippmann
2020-03-03 23:13:02

Bob Deblier
2020-03-03 23:13:22

Mario Hippmann
2020-03-03 23:13:47

Mario Hippmann
2020-03-03 23:14:51

Bob Deblier
2020-03-03 23:14:57

Balint Beni
2020-03-03 23:15:56

Mothy Reynolds
2020-03-03 23:21:22

Bob Deblier
2020-03-03 23:21:51

Mothy Reynolds
2020-03-03 23:22:49

Mario Hippmann
2020-03-03 23:26:01

Bob Deblier
2020-03-03 23:27:01

Mothy Reynolds
2020-03-03 23:27:07

Mario Hippmann
2020-03-03 23:29:24

Bob Deblier
2020-03-03 23:32:16

Bob Deblier
2020-03-03 23:36:31

Mario Hippmann
2020-03-03 23:37:46

Bob Deblier
2020-03-03 23:38:40

Mario Hippmann
2020-03-03 23:39:49

Vinicius Silva
2020-03-03 23:41:28

Mario Hippmann
2020-03-03 23:42:52

Bob Deblier
2020-03-03 23:44:15

Mario Hippmann
2020-03-03 23:45:19

Bob Deblier
2020-03-03 23:46:01

Mario Hippmann
2020-03-04 00:10:16

Bob Deblier
2020-03-04 00:11:18

Mario Hippmann
2020-03-04 00:19:59

Bob Deblier
2020-03-04 00:20:32

Bob Deblier
2020-03-04 00:21:23

Mario Hippmann
2020-03-04 00:22:19

Bob Deblier
2020-03-04 00:22:58

Mario Hippmann
2020-03-04 00:24:19

Bob Deblier
2020-03-04 00:24:57

Mario Hippmann
2020-03-04 00:31:30

Mario Hippmann
2020-03-04 00:32:08

Mario Hippmann
2020-03-04 03:24:56

Mario Hippmann
2020-03-04 03:24:59

Mario Hippmann
2020-03-04 03:25:03

Mario Hippmann
2020-03-04 03:25:07

Mario Hippmann
2020-03-04 03:25:32

Bob Deblier
2020-03-04 03:27:44

Bob Deblier
2020-03-04 03:33:13

Mario Hippmann
2020-03-04 03:33:55

Bob Deblier
2020-03-04 03:34:48

Mario Hippmann
2020-03-04 03:35:27

Bob Deblier
2020-03-04 03:37:44

Mario Hippmann
2020-03-04 04:24:46

Bob Deblier
2020-03-04 04:26:08

Peter Ede
2020-03-04 09:18:26

Mario Hippmann
2020-03-04 12:41:18


原文網址 Mario Hippmann
2019-12-29 19:58:33

What happend here?

The one Pic Shows how i should be, the Other has a Strange flat area in the Print

翻譯年糕

Mario Hippmann
2019-12-29 20:24:43


 

討論主題

全不選 常用關鍵字