Anycubic Photon Printer Owners 造訪社團 » 用戶發文

I have a bit of a conundrum. I bought 1L of the monocure clear, and 1L of their white, as well as the CMYK pigment set. But I have no bottles to hold the various mixes I want to make. Does anyone know of a good place where someone can just buy a couple opaque, wide mouth plastic bottles? All I can find are wholesale packaging outlets that want me to buy 500 of them.

翻譯年糕

Been seeing this more and more lately, even on models that printed beautifully before. I don't see any reason why this one would fail, that hole goes all the way through, so their shouldn't be suction forces. I don't think there is any way to rotate that to reduce the surface area.

Not sure what to do

翻譯年糕

Has anyone made a "zwobs" test file? Seems its a really common issue, and I want to verify for sure whether or not I've got them. So far all my prints have been so short I don't see them until they're done, so I honestly have no idea.

翻譯年糕

What would make my models lose detail on the side closest to the build plate? I often print my miniatures looking like they're on a reclining bed of needles, and they always end up having overly smooth, poor resolution on their back.

I thought initially I wasn't being careful enough while cleaning and wasn't getting all the resin off the back, but its not the case. What else could it be?

翻譯年糕

Finally starting to work on the projects that I bought this printer for! Namely, replacing the cardboard figures in my favourite games with 3d minis. First up, the stone golem in Gloomhaven. This was in monocure green, although I think for the final version I'm gonna mix up some really translucent blue and put an led in it.

翻譯年糕

Tried to cure and filter the resin out of my IPA in the cleaning tank with a coffee filter. Before it was clear with a bit of dye settled in the bottom, now it looks like the blue milk from Star Wars ?

Anyone had luck with filtering out IPA?

翻譯年糕

Some Anycubic reps lurk this group, right? Can they tell me why Anycubic refuses to ship to Canada from the United States? I want to buy an i3 mega, but shipping from china is $200! ?

My photon came from china, but it through DHL for cheap

翻譯年糕

Tried the Monocure Rapid Green today. Its not on the spreadsheet so I figured I'd leave the settings the same as I had for the Anycubic green* and see what happens.

I was delighted to see how easy it was to peel the prints off the bed, until I realized why... 75% of the light supports had broken off, and 2 of the 3 prints had failed as a result. The third, which had medium supports, printed nearly perfectly however.

They are definitely noticeably softer than my earlier prints, and its night time so I'll have to wait to cure them tomorrow but they are definitely more opaque. I'm not sure where to go from here, up the cure time and go back to having to use a 4 foot pry bar to get the prints off, or start using medium supports all the time, which I don't really like.

*(Layer: 0.03mm, Exposure 10s, off time 1s, bottom exposure 45s, Bottom layers: 8)

翻譯年糕

oh, one more question. I always end up throwing my build plate out of alignment when I'm popping off the prints, forcing me to re-level it for every print job. Is there a better way to hold it to keep that from happening, or do I just keep doing it this way?

翻譯年糕

You can only see it under the perfect lighting conditions, but my FEP film is starting to get little dimples from the printed supports. I've only been at this for a week, however. Am I doing something wrong? How long should the FEP film last? It seems to have a bit scratched by my paper towel too, which is a bit surprising

翻譯年糕