Anycubic Photon Printer Owners 造訪社團 » 用戶發文

Originally sculpted this model as a private commission to a customer for bronze casting(big size). But i couldn't help myself to print this small version for my personal collection.

翻譯年糕

Cat and Mouse :) Here are some prints which i printed lately and primed today.

翻譯年糕

I purchased gray, clear and white Esun General Purpose Resin a while ago as it was cheap.
Overall i liked the outputs from all three, especially from the gray one (the skull i shared in the group). But the calibration test shows that they are slightly slow curing resins and for best results all of the three need around 20 seconds. The white one i tried has best spot between 4-5 numbers at 6-to-60 test which is nearly 26-27 seconds for 0.050 thickness.
I printed this model before doing the calibration test at 15 seconds. It seems fine but i believe i will get better result when i go up to 24-26 seconds. Is there anyone tested this brand and got different results?

翻譯年糕

I used gray colored Esun General Purpose Resin. The print seems fine overall. I think exposure time needs to be revised for better details. Printed at 0.050 with 15/6.5/50/8. Size is 4.5 cm from chin to top. No primer yet. Just pure grey color resin.

翻譯年糕

Yesterday and today two prints failed. Honestly, I was thinking that people are a bit over cautious about the stock USB drive. But it seems that people are right that stock USB drive is really bad quality.

I've tried to transfer the photon files from the USB to my computer to see if the files were OK and voila, the first file that stopped gave an I/O error on computer. The second one was transferred without any problem but i decided to check it with Validator and voila again, the file was corrupted where it has stopped.

So if any new users reading this, please just throw the stock USB drive (or just use it on unimportant personal file transfers) and use a quality USB drive for the printer.

翻譯年糕

This was one of my portfolio piece from years ago. I was thinking to do a body for him but couldn't have time and was sitting in my hard drive for a long time. This test print made me to think about working on it again because the result that i got with Photon is so motivating! Hope you like it too.

Modified top side to make it a wacom pen holder =) .

P.s: Maybe not this but i'll share some of my models here with this great community for sure!

翻譯年糕

Hi everyone. Here is my first share, first prints. :)

After my bad luck with my first Photon which came covered with resin and didn't work, i ordered once more and this time the new printer came in perfect condition and worked great.
It's great and really fun to print my own models at this detail level.
These prints are at 0.050 thickness. Anycubic default Green, primed.

翻譯年糕

Hi guys,

I've purchased Photon a week ago and after customs clearance it arrived just today. It will be first time with this type of printer also first time i will deal with resin.

I opened the box. Every additional parts seemed ok except the printer. First i realised some sticky surface on the side of the printer door. Then when i tried to remove vat tank i realised it is sticky between fep surface and lcd screen below. I carefully removed the vat tank and it seems some resin leaked over all over the red surface (on the corners, on sides of fan). The 250g example resin is clean so i believe it is either a used one or occured after test if they are doing any.
I don't know if the printer will work or not. I don't know if it is a "don't worry it is easy to fix" problem or a bad one:(

Please help me about what should i do now.
I have read and noted about tons of problems from this group and reddit since i made my order. I didn't expect to experience such hard situation from the first step. I don't know what to do.

翻譯年糕