Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Aaron Swickard
2019-04-16 00:12:32

Are there any resins out there that will work with a heat gun to be bent into shape? Or will I have to mix a bit of the flex resin into it? I have a figure that I'm making armor for but I'm not sure of the angles. Easiest way I can think of is to print the armor flat and just bend it over the places it needs to be.

翻譯年糕

原文網址 Aaron Swickard
2019-03-17 10:14:11

Asking again. Why is ChiTuBox causing these artifacts that ruin prints? They dont show up on the validator and only happen when using ChiTuBox

翻譯年糕

Mike Biggs
2019-03-17 10:18:15

Vinicius Silva
2019-03-17 10:27:30

Aaron Swickard
2019-03-17 10:30:31

Sen Kun
2019-03-17 18:30:52

Aaron Swickard
2019-03-17 21:33:36

Sen Kun
2019-03-17 22:05:35

原文網址 Aaron Swickard
2019-02-20 08:33:04

This a slicer issue or am I losing the screen? Odd little flaps that dont show up on the validator. They're only a layer or two each.

翻譯年糕

Aaron Swickard
2019-02-21 00:15:57

原文網址 Aaron Swickard
2019-01-30 10:20:54

I need to print more mediums and lights. I'm a little top heavy at the moment.

翻譯年糕

Mikko Asikainen
2019-01-31 02:29:03

原文網址 Aaron Swickard
2018-12-24 03:08:22

Anyone else encountering a problem where Chitubox displays nothing on the screen? Reinstall does nothing. It's just gone.

翻譯年糕

Ian Dorrington
2018-12-24 03:16:45

Susan Sioux Mercer
2018-12-24 03:25:24

Sen Kun
2018-12-24 03:30:34

Matthew Tippets
2018-12-24 04:18:13

Jake Walker
2018-12-24 04:23:51

Aaron Swickard
2018-12-24 04:39:17

Sen Kun
2018-12-24 04:47:05

Sen Kun
2018-12-24 04:48:22

Jake Walker
2018-12-24 04:54:19

Sen Kun
2018-12-24 04:54:58

Sen Kun
2018-12-24 04:55:30

Nikola Petrov
2018-12-24 06:28:25

谢信福
2018-12-24 10:49:56

原文網址 Aaron Swickard
2018-12-15 21:23:24

Biggest thing I've printed yet. Battletech Omega from Gambody in nscale. Still working on the Marauder IIC but it feels like that thing was custom made to screw with anyone trying to print it because of all the holes in the mesh.

翻譯年糕

Jeff Kodysz
2018-12-16 06:36:12

Aaron Swickard
2018-12-16 08:22:12

原文網址 Aaron Swickard
2018-11-14 21:18:00

All the 'Mechs I've printed so far. Some bare, some primed, some with the first basecoat down. I realize now that I've only printed a couple mediums. That will have to be fixed.

翻譯年糕

Bronson Ferri
2018-11-14 21:45:48

Aaron Swickard
2018-11-14 22:00:42

原文網址 Aaron Swickard
2018-11-07 08:09:14

It's tough getting good pictures anywhere with just the basic transparent resin but here's a Mercy bust that I printed out for my sister. Later pictures to come after she gets painted up.

翻譯年糕

原文網址 Aaron Swickard
2018-10-30 03:07:57

All 4 'Mechs so far. The Orion ended up smaller than I thought it would but oh well. 250 ml actually goes pretty far since I still have just over 1/3 of the original sample that came with it. Taking a break from printing while I wait for my next batch of resin to get here and to get these all cleaned up. I found out the only things worth hollowing are the torsos as well.

翻譯年糕

原文網址 Aaron Swickard
2018-10-27 22:41:39

First miniature is a success! Only problem I'm having is I have trapped uncured resin in certain parts of the figure that slowly leak out. I think that was due to improper placement of vents and them being too small. Otherwise it's almost perfect. It's tough to see the detail to remove the support sprue marks so I'll hit it with the UV lamp and then dust it with spray primer to see them better. Hopefully that takes care of the uncured resin as well.

翻譯年糕