Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Michael Goldberg
2019-01-08 13:05:36

I'm having some trouble when printing. All of my recent prints have been printing without the first base layer. At least that what it shows on the small LCD screen. But this print has gone without showing 3 layers. I'm not sure why but I'm very concerned. I sliced in chitubox.

I know this is a bit garbled but I'm tired and a bit distracted and in a rush. I can explain if needed.

翻譯年糕

Richard Shapiro
2019-01-08 13:10:47

Michael Goldberg
2019-01-08 13:15:26

Richard Shapiro
2019-01-08 13:17:02

Richard Shapiro
2019-01-08 13:17:16

Michael Goldberg
2019-01-08 13:42:43

Giancarlo Arriola
2019-01-08 14:12:36

Michael Goldberg
2019-01-08 14:15:31

Shaun Khiu
2019-01-09 13:37:17

原文網址 Michael Goldberg
2019-01-06 07:56:53

Need some advice. Trying to print this huge piece. Tried it earlier but it failed before the supports could even be printed. I was using 50% heavy support density shown below. I'm now thinking about using 75% density with .8 or 1.0mm top diameter and 1.2mm lower and bottom diameter. I can't put a raft in because it's outside the build volume and I fear it still wouldn't print. This orientation and oriented the opposite way, vertically down, are the only orientations I can print in. The part is just too large to print any other way. Any suggestions?

Also, yes, I've considered printing it in 2 smaller parts but I'd then I might lose some detail and the top surface has be completely smooth (joint-wise speaking). Printing in two would result in a ragged joint. I've printed a different part in 2 sections and that was the result. Also resulted in a wavy surface on 2 sides, much moreso on the bottom surface close to the build plate.

翻譯年糕

John Boyington
2019-01-06 08:21:54

Evangelos Agas
2019-01-06 10:07:01

Michael Goldberg
2019-01-06 10:07:15

Michael Goldberg
2019-01-06 10:08:04

John Boyington
2019-01-06 10:26:05

原文網址 Michael Goldberg
2018-12-28 15:18:33

What do you guys think would be the best way to print this? I've tried flat and level and it printed well but the "top" was flattened and round things were only partially round. There was also a cured film covering one of the magazine sections and detail on the support half was obviously shot. I'm thinking of decreasing the amount of supports on the current supported model and possibly trying a vertical orientation.

翻譯年糕

Mark Wardle
2018-12-28 15:27:22

Michael Goldberg
2018-12-28 15:39:04

Robert Mako Sharkey
2018-12-28 16:59:00

Josh Crosier
2018-12-28 21:23:03

Michael Szita
2018-12-28 22:05:23

Andy Smith
2018-12-28 23:49:11

Josh Crosier
2018-12-28 23:53:29

Michael Goldberg
2018-12-29 07:55:38

Michael Goldberg
2018-12-29 07:56:02

Michael Goldberg
2018-12-29 07:56:17

Michael Goldberg
2018-12-29 07:56:53

Josh Crosier
2018-12-29 07:57:46

Michael Goldberg
2018-12-29 08:00:05

Michael Szita
2018-12-29 08:57:04

Arizeta Zaft Aeug
2018-12-29 11:04:28

Arizeta Zaft Aeug
2018-12-29 11:04:55

Ulrich Rüstungjäger
2018-12-29 11:37:54

Felipe Martinez
2018-12-29 11:50:39

Andy Smith
2018-12-29 18:23:09

Wesley Dowell
2018-12-30 00:07:35

原文網址 Michael Goldberg
2018-12-26 06:17:42

What do you guys and gals think of my new printer set up? And Happy Holidays too.

翻譯年糕

Ekaterina Vitalyevna
2018-12-27 23:30:46

原文網址 Michael Goldberg
2018-12-23 18:32:50

I have bad luck with resins... Still can't get rid of the excess resin curing. I think I will try the suggestion of updating firmware.

翻譯年糕

Danny Lloyd
2018-12-23 18:34:05

Michael Goldberg
2018-12-23 18:37:05

Danny Lloyd
2018-12-23 18:39:51

Michael Goldberg
2018-12-23 18:41:09

Richard Shapiro
2018-12-23 20:18:23

Michael Goldberg
2018-12-24 02:42:34

Richard Shapiro
2018-12-24 04:36:05

Michael Goldberg
2018-12-24 06:27:35

Fred Breton
2018-12-24 09:39:12

Shawn Atlas
2018-12-24 10:26:43

Bradley VanScoyk
2018-12-24 10:48:17

原文網址 Michael Goldberg
2018-12-23 01:38:10

Need more help. First print with Wanhao water washable gray. Came out like crap. 10 microns at 7 secs with 8 base layers at 90 seconds. Think I need more supports or longer exposure? Also, is the Wanhao water washable gray supposed to be so... Watery?

翻譯年糕

Sining Ong
2018-12-23 01:50:19

Fred Breton
2018-12-23 01:51:56

Fred Breton
2018-12-23 01:53:03

Danny Lloyd
2018-12-23 01:53:44

Danny Lloyd
2018-12-23 01:54:10

Michael Goldberg
2018-12-23 01:56:22

Michael Goldberg
2018-12-23 01:57:03

Michael Goldberg
2018-12-23 01:57:57

Fred Breton
2018-12-23 01:59:00

Michael Goldberg
2018-12-23 02:05:29

Fred Breton
2018-12-23 02:10:32

Fred Breton
2018-12-23 02:44:33

Fred Breton
2018-12-23 02:45:06

Fred Breton
2018-12-23 02:45:27

Charlie Anderson
2018-12-23 03:57:44

Danny Lloyd
2018-12-23 03:58:10

Michael Goldberg
2018-12-23 07:08:29

Michael Goldberg
2018-12-23 07:08:55

Michael Goldberg
2018-12-23 09:32:38

Charlie Anderson
2018-12-23 17:13:12

Thomas 'Noodle' Didcote
2018-12-23 21:35:17

Charlie Anderson
2018-12-24 04:26:51

Thomas 'Noodle' Didcote
2018-12-24 04:44:07

Charlie Anderson
2018-12-24 05:01:37

Jaco Norchie Nortje
2018-12-24 05:12:16

原文網址 Michael Goldberg
2018-12-21 15:17:00

Why do I keep getting this tabs? The last picture shows a short shot. The base is supposed to be 90°.

翻譯年糕

Dennis Tomson
2018-12-21 15:35:30

Michael Goldberg
2018-12-21 17:18:28

Richard Shapiro
2018-12-21 23:01:37

Dennis Tomson
2018-12-22 01:31:04

Michael Goldberg
2018-12-22 04:39:19

Michael Goldberg
2018-12-22 07:01:13

Richard Shapiro
2018-12-22 07:09:05

Michael Goldberg
2018-12-22 07:13:17

Michael Goldberg
2018-12-22 07:44:56

Richard Shapiro
2018-12-22 07:53:57

原文網址 Michael Goldberg
2018-12-19 10:34:14

Having some trouble. I'm thinking this is overexposure but then the far left and middle pieces have problems. This was printed at 10 micron, 14 second exposure, 8 base layers, 90 second base layers, 1 sec. off time. I'm planning on sell these and more designs on a small scale commercial level at 20 and 10 micron so I need to get exposures down pat. I'm using Anycubic Gray resin. Soon I'll be using Wanhao water washable gray.
Picture 2: the resin between rows 2 and 3 shouldn't be there.
Picture 3: the long thin stretch of resin shouldn't be there.
Picture 4: there's small blobs of resin on top of all the little cans.
Picture 5: the right one should look like the left.
Picture 6: if you look at the far piece, there's blobs of resin on the side that shouldn't be there.
Picture 7: the left one should look like the right.
Picture 8: I'm not sure about this. I modeled it more detailed but it just looks funky.

I'm concerned about these.

翻譯年糕

Chris Cardinal
2018-12-19 10:47:56

Michael Goldberg
2018-12-19 11:01:04

Philippe Maegerman
2018-12-19 23:17:02

Michael Goldberg
2018-12-21 12:24:47

原文網址 Michael Goldberg
2018-12-18 10:49:49

2 newb mistakes in 2 days:
1. Forgot to tighten the screw on top of the build plate. Caused a failed print.
2. Forgot to put resin in the vat before starting a print. Stopped it before it got too far.

翻譯年糕

原文網址 Michael Goldberg
2018-12-17 05:37:12

I'm trying to make my own curing chamber using a square metal tin and UV lights. Where do you get your UV light strips from? I'm also thinking about using straight light strips instead of flexible ones.

翻譯年糕

Adam Horton
2018-12-17 05:41:47