Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Leon Skopilianos
2019-09-23 05:14:29

Looking for advice.
How would you orient and do this print on an object like this?

The bottom flat mates with another part.

Would it have to be hollow?

Thanks in advanced

翻譯年糕

Jonathan Andersson
2019-09-23 05:37:17

Leon Skopilianos
2019-09-23 05:38:26

Jonathan Andersson
2019-09-23 05:39:13

Leon Skopilianos
2019-09-23 05:50:21

Jonathan Andersson
2019-09-23 05:51:00

Jonathan Alvarado
2019-09-23 08:55:20

Scott Pavlich
2019-09-24 09:54:14

原文網址 Leon Skopilianos
2019-07-15 08:26:52

Hey guys,
Looking for a recommendation to complement my photon. Another resin printer. My main issues with the photon are occasional build plate adhesion issues. Otherwise, I use castable resin. So typically a stronger UV would be preferred. I'm not totally against a true laser SLA also.

Budget? Less than form 3, more than photon?

翻譯年糕

Kenneth Jones
2019-07-15 08:28:40

Micah Vestal
2019-07-15 08:34:34

De Jesus
2019-07-15 08:35:21

Leon Skopilianos
2019-07-15 08:41:38

Leon Skopilianos
2019-07-15 08:42:42

Micah Vestal
2019-07-15 08:46:07

Curt Pangracs
2019-07-15 08:49:19

Scott Pavlich
2019-07-15 09:06:16

Leon Skopilianos
2019-07-15 09:13:23

Leon Skopilianos
2019-07-15 09:14:04

Jonathan Bollon
2019-07-15 13:48:15

Leon Skopilianos
2019-07-15 14:38:05

Leon Skopilianos
2019-07-15 14:40:00

Jonathan Bollon
2019-07-15 15:33:32

Leon Skopilianos
2019-07-15 15:49:57

Curt Pangracs
2019-07-15 19:29:16

Philippe Maegerman
2019-07-15 21:04:58

原文網址 Leon Skopilianos
2019-07-04 06:15:01

Hey guys, I'm playing with Anycubic Transparent Yellow resin. My supports are sticking like painfully well. Any tips of support interface settings (contact depth, shape, radius etc) that should help?

Also I've been thinking of adding about 15% monocure flex to the mix with anycubic trans yellow. Was wondering what regular layer cure times you'd suggest?

Any and all recommendations are greatly appreciated.

翻譯年糕

Jonathan Lopera
2019-07-04 06:28:51

Leon Skopilianos
2019-07-04 06:33:20

原文網址 Leon Skopilianos
2019-07-03 16:02:00

Hey guys, anybody got a link to the photon slicer? Cannot seem to find it on anycubic site.

翻譯年糕

John Lowry
2019-07-03 16:20:36

原文網址 Leon Skopilianos
2019-04-20 14:44:06

Hey guys,

Been printing great with FunToDo castable. However, I'm not getting a great burn-out. Ash left over is causing some terrible casts. Anybody got any advice as to the post print - before burn-out routine? My thought is perhaps the prints weren't cured enough as I follow the FunToDo burn out cycle (long not short).

翻譯年糕

原文網址 Leon Skopilianos
2019-04-09 20:38:32

Hey gurus! I need some help.
I've been getting some great prints now. Except the bottom of my rings are deformed. I am using a significant amount of supports on a 45 degree angle?
Any help?

翻譯年糕

Chad Elstad
2019-04-09 20:49:06

Julia von Pfaler
2019-04-09 21:40:35

Leon Skopilianos
2019-04-10 09:09:51

Leon Skopilianos
2019-04-10 09:10:59

原文網址 Leon Skopilianos
2019-04-06 16:26:27

So amidst my issues trying to get anything to stick to the build platform, I decided to try to sand my build plate. Seems a lot flatter now. Still not getting anything sticking to the build plate though. Have repeated the bed levelling multiple times. Any ideas guys? What grit finish would you leave on the sanded plate to help adhesion?
Information: Using monocure rapid resins trying about 110s bottom layer cure times - just trying to get something to stick...

翻譯年糕

Joe Broggio
2019-04-06 16:49:40

Leon Skopilianos
2019-04-06 16:53:31

Joe Broggio
2019-04-06 16:55:30

Leon Skopilianos
2019-04-06 16:57:06

Leon Skopilianos
2019-04-06 16:57:25

Sen Kun
2019-04-06 16:57:44

Joe Broggio
2019-04-06 16:58:18

Leon Skopilianos
2019-04-06 16:58:53

Leon Skopilianos
2019-04-06 16:59:19

Sen Kun
2019-04-06 17:02:55

Leon Skopilianos
2019-04-06 17:04:03

Leon Skopilianos
2019-04-06 17:04:35

Sen Kun
2019-04-06 17:05:40

Leon Skopilianos
2019-04-06 17:07:07

Leon Skopilianos
2019-04-06 17:52:16

Sen Kun
2019-04-06 18:34:18

Alex Munro
2019-04-06 20:04:06

原文網址 Leon Skopilianos
2019-04-04 17:42:07

Hey guys! Looking for some more advice. Say I'm printing a basic ring shape. What is the best orientation to print it?
I've tried 45 degrees with support (chitibox at around 65% density, medium)
But I find that I get some shape deformation on the bottom surface. Any ideas?

翻譯年糕

Leon Skopilianos
2019-04-05 06:55:58

原文網址 Leon Skopilianos
2019-03-31 18:24:56

Hey guys,
Looking for some advice. Lately, I've been having an issue where I get prints going nicely for awhile. Change nothing, but then the prints start failing. The failure mode is the base of the prints start sticking to the print platform but often come off only a few layers in. Even with bottom layers at approximately 80-100sec. Monocure rapid resin. I relevel, clean everything and sometimes it goes away, sometimes it doesn't.

The prints themselves are small rings, with medium to heavy auto support on chitibox.
What am I missing?

翻譯年糕

Stephen Lewis
2019-03-31 18:36:26