Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Nic Lim
2020-02-03 19:33:46

Hi everyone! Recently I've acquired the new Phrozen Transform, and luckily it works with chitubox so it's a seamless transition. Am wondering does the resin exposure test we have for the anycubic photon works with the Transform as well? Thanks in advance..!

翻譯年糕

原文網址 Nic Lim
2019-03-25 23:14:48

Prints came out perfect despite the raft coming loose from the plate. Got these prints after tuning the FEP sheet... Turns out I'm running it a bit loose all these while lol

翻譯年糕

Mark Wardle
2019-03-26 09:16:21

Nic Lim
2019-03-26 17:39:00

Paul Fagan
2019-03-29 22:28:05

Nic Lim
2019-03-29 22:39:34

原文網址 Nic Lim
2019-03-24 00:25:39

Just a helpful guide for tuning the FEP after changing it. I was having trouble with not being able to calibrate it properly as I wasn't sure what was the best way to check for the FEP frequency. Ended up with a bunch of weirdly warped prints..! Hope this is helpful.

翻譯年糕

原文網址 Nic Lim
2019-03-21 15:39:23

So am experimenting with some new resins, done the resin exposure test which shows column 7, 8, and 9 to capture most details. Took an average of 16s, then 14s and 12s with the results below. Also recently changed the FEP as it was FUBAR.. would the incorrect tension on the FEP causes layer shifts and warps?
I've done a dry brush on the monocure matrix to better show details.
Thanks in advance!

翻譯年糕

Jannick Langfahl
2019-03-21 20:08:26

Nic Lim
2019-03-21 20:14:23

原文網址 Nic Lim
2019-01-23 14:40:06

It's during prints like these that I'm glad the photon is in my life. 35 pieces of Tiny Trex keychains, printed with monocure rapid blue. Would've taken ages to print not to mention post processing on an fdm..!

Spent about 140ml of resin, took 6 hours x 5 runs to get them all printed. 7 copies per run.

翻譯年糕

Justin Wiggins
2019-01-23 14:49:52

Nic Lim
2019-01-23 14:54:36

Justin Wiggins
2019-01-23 15:07:11

Nic Lim
2019-01-23 15:10:38

Justin Wiggins
2019-01-23 15:14:39

Kelvin Pang
2019-01-23 15:29:36

Luke Forrest
2019-01-23 15:43:25

Nic Lim
2019-01-23 15:49:37

Nic Lim
2019-01-23 15:50:06

Zena Andreou
2019-01-23 16:50:06

Ekaterina Vitalyevna
2019-01-24 06:03:29

原文網址 Nic Lim
2019-01-21 16:45:05

Just want to share my "30 minutes curing chamber project" in hopes that it would be useful to someone here. No noticeable leak of UV light.. somewhere down the line I'm sure I'll build something much more reliable.

UV light is 405nm, 60 watts, sourced from Aliexpress.

"Chamber" cost me RM4, that's barely 1USD.

翻譯年糕

Ricardo Sebastian Ibacache Guerr
2019-01-21 20:59:40

Nicolas Belin
2019-01-22 08:46:32

Nic Lim
2019-01-22 09:20:22

Nikolas Willingham
2019-01-22 13:04:46

原文網址 Nic Lim
2018-12-27 12:40:01

30cm hellboy almost done! First big print on the photon. Figuring out how to separate the model to be photon-friendly was a challenge. The odd colors was because I was running out of resin so had to mix two batches of different resin. Glad everything turned out well.
Total print time so far is around 80 hours. Just had to sort out the cloak and tail next.
Model can be found free on myminifactory.com

翻譯年糕

Juanma Ferrer Martin
2018-12-27 17:42:38

Nic Lim
2018-12-27 19:20:37

Juanma Ferrer Martin
2018-12-27 20:01:42

Guajolote Messias
2018-12-28 01:01:45

Glenn Maes
2018-12-28 04:58:36

Guajolote Messias
2018-12-28 05:38:17

Nic Lim
2018-12-28 09:57:32

原文網址 Nic Lim
2018-12-12 20:39:57

So I do know the rule of thumb is to never print large surfaces flat to the plate. But for this panel, where the bottom is hollow, could I get away with this? or is it better to orient it 15 degrees along the long side? Thanks for any and all feedback.

翻譯年糕

Chad Elstad
2018-12-12 20:47:23

Richard Shapiro
2018-12-12 22:03:59

Richard Shapiro
2018-12-12 22:04:32

Nic Lim
2018-12-13 08:22:50

Nic Lim
2018-12-13 08:23:29

原文網址 Nic Lim
2018-12-08 13:04:54

First successful print! Mini thanos in conjunction with release of Avenger's End Game trailer.
Bathed in acetone, prime, sanded and primed again. Just need to paint it now.

翻譯年糕

原文網址 Nic Lim
2018-11-29 09:01:32

Greetings! Been lurking for awhile and finally pulled the trigger, printer is on the way!
Would like to ask if a 70% rubbing alcohol solution be sufficient to clean the parts? Where I'm from it's a bit difficult to get 99% alcohols. Appreciate the feedbacks and thanks in advance!

翻譯年糕