Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Giosnò Dizze
2020-03-10 02:36:21

When chitubox says you need 40g in vat you put 50g but isn't enough ? I've tried to refill but was too late

翻譯年糕

Aaron Shrive
2020-03-10 02:38:29

Gilboy Hill
2020-03-10 03:03:58

Giosnò Dizze
2020-03-10 03:22:35

Aaron Shrive
2020-03-10 03:23:25

Giosnò Dizze
2020-03-10 03:24:53

Giosnò Dizze
2020-03-10 03:25:57

Alexx Butnotalex
2020-03-10 03:37:38

Gilboy Hill
2020-03-10 04:08:36

Richard Humble
2020-03-10 05:31:30

Ben Messer
2020-03-10 06:43:45

Wes Mischke
2020-03-10 06:50:01

Petr Grössl
2020-03-10 18:24:36

Petr Grössl
2020-03-10 18:37:21

Juan Pablo Bagnon
2020-03-10 20:40:38

原文網址 Giosnò Dizze
2019-12-24 05:24:19

Lithophane test printed direct on plate, layer height 0.04 resin plant based by anycubic

翻譯年糕

Dustin Oliverius
2019-12-24 05:26:11

Dustin Oliverius
2019-12-24 05:26:25

Alexander Bayerdorffer
2019-12-24 05:32:16

Giosnò Dizze
2019-12-24 05:33:29

Dustin Oliverius
2019-12-24 14:01:23

Richard Clinton
2019-12-24 14:12:18

Dustin Oliverius
2019-12-24 14:15:37

Richard Clinton
2019-12-24 14:18:04

Lee Baxter
2019-12-24 17:24:30

Justin Leone
2019-12-24 18:56:38

Peter Mark Ballard
2019-12-24 19:03:07

Russ Greene
2019-12-24 21:18:45

Giosnò Dizze
2019-12-24 21:49:38

Tim Wilson
2019-12-25 00:25:22

Dustin Oliverius
2019-12-25 01:30:18

Dustin Oliverius
2019-12-25 01:31:19

Tyson Moran
2019-12-25 02:05:37

原文網址 Giosnò Dizze
2019-11-23 01:10:08

Hi to all maybe someone can help me I'm printing a batch of keychains with other resins everything goes fine now I'm trying new anycubic eco resin in orange and i have issues in details, i've done settings test and using line 8. Red one was printed with druckwege resin and it's ok other one is printed with anycubic eco and loses lot of details how can i solve ? Thank you

翻譯年糕

原文網址 Giosnò Dizze
2019-03-27 02:24:04

Hi i've to print these blocks . I'm at the third attemp first two times i've tried without support and parts sticks on fep. Thrid time as suggested I've tried lift by 5mm a use medium support always print flat and support stat on plate but print is again stick on fep. Can somebody help me?

翻譯年糕

Richard Pigott
2019-03-27 02:26:41

Chris Smith
2019-03-27 02:36:31

Nick Thompson
2019-03-27 16:19:14

原文網址 Giosnò Dizze
2019-03-22 00:43:18

After this morning print fail I've releveled bed using flint method. Now if I go home or start a print z goes down until make TRRRRRR noise. Why? All is ready for print there's a way for solve without clean everything again? Thanks to all

翻譯年糕

Zena Andreou
2019-03-22 01:05:36