• 3D列印服務
  • COSPLAY 3D 建模
  • #maker+t=market
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Testo Il Testabile
2020-01-24 23:42:57

Does it exist a (reasonably priced and easily printable) "eco" resin that I can touch barehands (it's okay to wash them immediately after) and breath without worries (I do have a destinkynator with active carbon filter and it helps but is not enough for the smell)?

翻譯年糕

Bob Deblier
2020-01-24 23:46:00

James Hendrix
2020-01-24 23:48:23

James Hendrix
2020-01-24 23:50:06

Testo Il Testabile
2020-01-25 00:00:22

Zena Andreou
2020-01-25 00:39:23

Benny Woolley
2020-01-25 01:21:46

Jim Monaco
2020-01-25 04:04:32

Marc Richards
2020-01-25 04:16:37

Marc Richards
2020-01-25 04:17:44

Dallas Winston Fitzgerald
2020-01-25 04:30:43

Theo Brinkman
2020-01-25 21:49:23


原文網址 Testo Il Testabile
2020-01-16 01:47:25

My take of the DeStinkyNator for the Photon S, print these: https://www.thingiverse.com/thing:4082951 https://www.thingiverse.com/thing:4097256 and on top of them you will need: 8cm fan raw activated carbon some rubber bands a short length window foam seal or equivalent some plugs and/or eletrical skills I spraypainted the destinkynator itself, then used just the activated carbon in the homemade filter grid (adding a layer or worse two of filter foam was blocking too much the air flow). Results are encouraging: I printed the 2 hours test cube in my other recent post, and I could only smell some weak whiff and nothing else. It's damn noisy though when under the printer, during dry run tests I could only hear a slight fan noise. 翻譯年糕

Rob van Doorn
2020-01-16 03:33:40


原文網址 Testo Il Testabile
2020-01-15 20:50:05

This cube was a test for my FDM printer which I scaled down to exactly 1cm sides.

Stuck directly to plate as I don't care about elephant foot.

Z dimension is exactly 1cm, X and Y are 1.03cm. I know prints off the photon (S) are not supposed to be 100% dimensionally exact because resin can expand and/or contract, yet is there a way to make the object more reliably dimensioned without scaling XY to 97%? (if it's even proportional and constant depending on the object size)

I could try lowering the exposure time to see if it was because of the bleeding, yet for now getting your input is faster than another 2hrs print at 0.02mm layer height ;)

翻譯年糕

Andrew Rosenthal
2020-01-15 20:59:41

Alvydas Jatkialo
2020-01-15 21:00:01

Alvydas Jatkialo
2020-01-15 21:04:30

Testo Il Testabile
2020-01-15 21:06:11

Alvydas Jatkialo
2020-01-15 21:07:10

Stefan Ritchie
2020-01-15 21:08:46

Alex Clarke
2020-01-15 21:09:34

Testo Il Testabile
2020-01-15 21:11:52

Peter Csaki
2020-01-15 21:17:41

Derek Reihe
2020-01-15 21:20:04

Dallas Winston Fitzgerald
2020-01-15 21:22:04

Testo Il Testabile
2020-01-15 21:28:18

Derek Reihe
2020-01-15 21:29:11

Alex Clarke
2020-01-15 21:33:54

Testo Il Testabile
2020-01-15 21:45:26

Derek Reihe
2020-01-15 21:46:34

Testo Il Testabile
2020-01-15 21:47:35

Alexander Bayerdorffer
2020-01-15 21:54:31

Testo Il Testabile
2020-01-15 21:55:00

Philipp Nguyen
2020-01-15 22:01:09

Alexander Bayerdorffer
2020-01-15 22:03:21

John Boyington
2020-01-15 23:40:25

John Boyington
2020-01-15 23:40:42

Testo Il Testabile
2020-01-15 23:45:33

John Boyington
2020-01-15 23:59:20

John Boyington
2020-01-16 00:01:41

Kory Sebby
2020-01-16 00:11:42

Scott Clark
2020-01-16 05:44:48

Scott Clark
2020-01-16 05:48:25

Scott Clark
2020-01-16 05:49:54

Samson Chen
2020-01-16 06:08:28

Scott Clark
2020-01-16 06:24:30

Shimbo Sean Bland
2020-01-16 06:44:41

Testo Il Testabile
2020-01-16 06:46:25

Robert Pope
2020-01-16 20:32:17

Testo Il Testabile
2020-01-17 03:00:24

Phil Riley
2020-01-17 14:30:21


原文網址 Testo Il Testabile
2020-01-04 05:20:32

First print ever, skipped anything test/demo related and cut to the chase: my application are teeth models.

Read everything and beyond while on vacation when the unopened Photon S was waiting for me to come back, sealed with kapton the borders of the screen, leveled with the printer paper sheet method, checked the FEP to be at 297Hz, room temperature just shy of 19°C, translucent green resin that everyone seems to be getting bundled with their S's, poured just a few mm's in the VAT, 0.02mm layer, 4 bottom layers at 60s and the rest at 8s, hollow model with 1mm thick walls, 3 holes on the bottom and placed a tube in meshmixer from one side to the other near the base; got reassuring plopping sound at most plate risings.

Gosh the smell! Headache and irritated nasal cavities, missus yelling at me, but the DeStinkyNator is a long-ass print and I am actually thinking about just building something with maybe wood PVC and what else. Used no gloves up to this point as I'm used to handle dangerous stuff without ever touching it, so my fingers never went on the resin, nor the resin on anything else except the vat.

Two hours print, after which I rotated the plate 90° so resin could drip back in the vat. Now the printer is resting while covered with the box it was shipped in, so no light whatsoever hits it, because sure as heck I don't plan on refilling the tank each time, even if my prints will be mostly far apart.

In the upcoming days I will get to building a handmade destinkynator, and wash/cure the model (UV strips are still on the way but I've got a weird old machine with couple Philips UV tubes inside that I can use).

I was expecting drama at the first go, and had a lot of uncertanties since I supposed I had to increase the exposure time, but all was way smoother that I thought (model included ? )

翻譯年糕

David Minford
2020-01-04 06:40:59

Brian Gabriel
2020-01-04 08:30:31

David Minford
2020-01-04 09:36:33

Johnny Grant
2020-01-04 10:24:03

Testo Il Testabile
2020-01-04 15:54:35

Testo Il Testabile
2020-01-04 15:57:38

Sander van Deijl
2020-01-04 16:52:51

Testo Il Testabile
2020-01-04 20:42:39

Lucas Parard
2020-01-05 00:07:27

Testo Il Testabile
2020-01-05 00:10:05

Bob Smith
2020-01-05 00:26:35

Lucas Parard
2020-01-05 00:37:36

Testo Il Testabile
2020-01-05 00:39:51

Lucas Parard
2020-01-05 01:08:46

Testo Il Testabile
2020-01-05 06:17:20

Lucas Parard
2020-01-08 05:52:10

Lucas Parard
2020-01-08 05:52:15

Testo Il Testabile
2020-01-09 00:39:13

Lucas Parard
2020-01-09 01:02:42

Lucas Parard
2020-01-09 01:02:47

Testo Il Testabile
2020-01-09 02:17:38

Lucas Parard
2020-01-09 02:46:29


原文網址 Testo Il Testabile
2019-12-30 04:02:04

After extensive information digging there are two doubts I still have.
1) In the FEP installation videos I see at the very end a scalpel is used to remove excesses out of the vat, doesn't this ruin the inside surface of the metal by carving it with the blade? I would prefer to cut it with something else, maybe small precision scissors, less accurate but leading to no damage to the metal surface
2) I will be using the printer occasionally, and usually you get warned about resin getting "old", and especially leading to problems if left in the vat where it might get solid. Would covering the whole printer with a heavy black cloth, stopping 100% of the light, be equivalent to move the residual resin back into the bottle after the print? Also, have tests been done to see for how long can a resin bottle be proficiently used in time if stored in optimal conditions (which are these conditions?)

翻譯年糕

Quinn Mehling
2019-12-30 04:16:31

Testo Il Testabile
2019-12-30 05:20:20

Alexander Bayerdorffer
2019-12-30 06:49:41

Quinn Mehling
2019-12-30 07:09:57

Quinn Mehling
2019-12-30 07:11:52

Testo Il Testabile
2019-12-31 01:38:57

Quinn Mehling
2019-12-31 02:03:27

Testo Il Testabile
2019-12-31 02:42:56


 

討論主題

全不選 常用關鍵字