Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Jonathan Cipryk
2019-07-31 20:57:29

Hey Folks, I had two of the same prints with identical defects after many successes with no changes in setup. The film is pretty new and looks good, but there was some sticking to the film both times when I drained the vat to inspect. Before I change the film I thought I would put this out there for suggestions/ confirmation. Thanks!

Elegoo grey, 10% tenacious.
.1mm @ 15 seconds( based on resin test, upped from 14 seconds previously)
8 bottom layers 100 seconds.

Light saber parts.

翻譯年糕

Iñigo Sordo
2019-07-31 21:03:10

Matt Hockenheimer
2019-07-31 21:04:44

Mark Kozik
2019-07-31 21:06:14

Bob Deblier
2019-07-31 21:12:01

Greg Kourakos
2019-07-31 21:13:03

Richard Flanagan
2019-07-31 21:41:38

Jonathan Cipryk
2019-08-01 06:57:14

Jonathan Cipryk
2019-08-01 07:38:11

Jonathan Cipryk
2019-08-01 07:39:20

Jonathan Cipryk
2019-08-01 11:54:38

Bob Deblier
2019-08-01 14:41:22

Kevin Boogaard
2019-08-01 15:16:12

Jonathan Cipryk
2019-08-01 21:39:03

Bob Deblier
2019-08-01 21:42:53

Jonathan Cipryk
2019-08-01 21:50:18

Bob Deblier
2019-08-01 21:50:48

Jonathan Cipryk
2019-08-01 21:51:44

Bob Deblier
2019-08-01 21:52:42

Jonathan Cipryk
2019-08-02 20:18:00

Jonathan Cipryk
2019-08-10 22:39:05

原文網址 Jonathan Cipryk
2019-07-16 02:25:29

Hey Folks, Amazon Canada is out of Elegoo Grey $20/500ml . But Elegoo Red, White, Yellow are available for the same price. What is your experience with those other colours for printing detailed minis?

翻譯年糕

Fedor Pikus
2019-07-16 02:26:25

Jonathan Cipryk
2019-07-16 02:47:30

原文網址 Jonathan Cipryk
2019-06-04 03:30:26

Hey Folks, I bought a bottle of AC White and ran some resin tests. The results of the 2-20 tests weren't great at the 10th test, so I ran the slow test for 50u.10-100 test.

The 6th print looks best to me, I'm reading this wrong :) , can you tell me what exposure time you see?

翻譯年糕

Bob Deblier
2019-06-04 03:35:05

Richard Thomas
2019-06-04 03:37:35

Will Koone
2019-06-04 03:38:00

Bob Deblier
2019-06-04 03:40:42

Jaime Cuéllar López
2019-06-04 03:41:50

Leonardo Delgado
2019-06-04 03:52:20

Jonathan Cipryk
2019-06-04 04:10:43

Jonathan Cipryk
2019-06-04 04:30:11

Jonathan Cipryk
2019-06-04 04:33:20

Will Koone
2019-06-04 04:39:05

Jonathan Cipryk
2019-06-04 04:56:07

Leonardo Delgado
2019-06-04 05:09:31

Leonardo Delgado
2019-06-04 05:11:08

Jonathan Cipryk
2019-06-04 05:19:54

Vinicius Silva
2019-06-04 05:34:42

Stefan Giudici
2019-06-04 05:36:54

Vinicius Silva
2019-06-04 05:40:06

Vinicius Silva
2019-06-04 05:40:45

Jonathan Cipryk
2019-06-04 06:16:40

Jonathan Cipryk
2019-06-04 06:19:35

Elvin Torok
2019-06-04 06:53:43

Jonathan Cipryk
2019-06-04 07:03:34

Vinicius Silva
2019-06-04 07:18:59

Vinicius Silva
2019-06-04 07:19:44

Stefan Giudici
2019-06-04 07:33:56

Jonathan Cipryk
2019-06-04 07:57:27

Jonathan Cipryk
2019-06-04 08:02:02

Vinicius Silva
2019-06-04 09:21:21

Jonathan Cipryk
2019-06-04 12:06:15

Björn Ståhlnacke
2019-06-05 05:43:13

Björn Ståhlnacke
2019-06-05 05:44:03

Jason Saiter
2019-06-05 22:07:15

Vinicius Silva
2019-06-05 22:08:48

原文網址 Jonathan Cipryk
2019-05-18 10:21:25

SOLVED - It really wasn't level, switched to the Flint Read Method - Hi Folks, any suggestion on this problem. New printer this week, larger prints are falling off the plate. The Photon cube won't stay either. Yet I've printed 5 miniatures at once earlier today. After a several fails I've corrected several things but I'm out of ideas...
1. I'm confident with the paper leveling method, 2. reduced the amount of resin in the vat, 3. the FEB looks ok, 4. added heavy supports and increased the raft size...

The following picture has a large raft , the BET is 100, 8 layers, 1.0MM , The photon demo cube is what it is.

Thoughts and suggestions are most welcome :)

Thanks!!

翻譯年糕