Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 John Adkins
2020-03-28 02:57:04

Question about resin prints. . . what kind of heat resistance do resin prints have? Could you for instance use them to print a fan vent for your FDM printer (the one I have now is PETG.

翻譯年糕

Simon Wilson
2020-03-28 02:59:13

Lots of people have done this in this group, and when I refine my design (and finish my resin heater) I'm going to do it too!

Ryan Moore
2020-03-28 03:19:17

I did this but the Anycubic gray resin I used was brittle and broke in a few places. I used it anyway and it held up to the heat just fine

原文網址 John Adkins
2020-03-09 06:21:23

I picked up a pair of the Elegoo Mars metal vats for my Photon. Do I need to re-zero and re-level the bed or just go forward?

翻譯年糕

Scott Pavlich
2020-03-09 06:26:08

Carla Birch
2020-03-09 07:46:04

原文網址 John Adkins
2020-01-13 23:58:06

Denlee Paddy Rhodes
2020-01-14 02:57:59

Evan Rosario
2020-01-14 03:11:45

Denlee Paddy Rhodes
2020-01-14 03:26:19

John Adkins
2020-01-14 03:50:54

John Adkins
2020-01-14 03:52:42

Denlee Paddy Rhodes
2020-01-14 03:54:08

John Adkins
2020-01-14 03:54:52

Denlee Paddy Rhodes
2020-01-14 03:56:39

原文網址 John Adkins
2019-10-24 10:18:17

Fat Dragon Games goblin with axe printed on Anycubic Photon with no supports other than the one included to support the axe handle. Printed standing upright.

翻譯年糕

原文網址 John Adkins
2019-09-09 10:23:15

John Adkins
2019-09-09 22:19:12

Manuel Boria
2019-09-09 22:27:54

John Adkins
2019-09-09 22:31:27

John Adkins
2019-09-09 22:32:40

Manuel Boria
2019-09-09 22:33:57

John Adkins
2019-09-09 22:37:29

John Adkins
2019-09-09 22:37:38

原文網址 John Adkins
2019-09-08 11:04:47

原文網址 John Adkins
2019-09-07 20:49:23

原文網址 John Adkins
2019-09-05 08:08:12

Brett VanDyke
2019-09-05 08:16:19

Simon Wilson
2019-09-05 08:45:33

John Adkins
2019-09-05 08:46:26

John Adkins
2019-09-05 10:20:02

John Adkins
2019-09-06 12:06:37

Simon Wilson
2019-09-07 05:50:51

John Adkins
2019-09-07 06:18:17

Simon Wilson
2019-09-07 18:05:20

原文網址 John Adkins
2019-09-04 03:40:54

Hi all,

Our Photon arrives tomorrow and we have been consuming a ton of how to guides and videos. One thing that remains a bit unclear for me is this: do you need to drain and clean the vat after each print. To wit, I am spending a Saturday printing. I print Bob the Goblin. I want to print his wife Bobbette. Do I need to drain or do I just top off the vat and print - draining at the end of my printing session?

Also, are there any additional basic guides I should read after Flint Read's guide? Thanks!

翻譯年糕

Gregorey Savieo
2019-09-04 03:42:42