Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Rob Allison
2020-02-02 20:14:06

Any idea why these supports would fail? They were done in Prusa Slicer, with auto supports at 75%. I also added other supports manually. It seems like I've only had issues with supports failing with Elegoo grey resin for some reason. This was printed at 0.05 and 6 sec exposure on a Photon S. Also this is fresh off the printer, did not put in IPA bath yet.

翻譯年糕

Michael Fairley
2020-02-02 20:30:51

Rob Allison
2020-02-02 20:33:24

Vincent Balmont
2020-02-02 21:08:52

原文網址 Rob Allison
2020-01-10 21:26:28

Ok hive mind. Been printing tons of models on my Photon S without issue. Switched to Elegoo Grey and everything has gone to crap. I've tried adjusting settings, I've re-leveled with both the paper and Flint Read methods, I've changed the FEP, etc. This last print is the exposure test after yet another re-level. Any idea what might be happening?? Very frustrating after no issues for so long.

翻譯年糕

Sander van Deijl
2020-01-10 21:28:31

Brian Gabriel
2020-01-10 21:37:03

Rob Allison
2020-01-10 21:39:59

Sander van Deijl
2020-01-10 21:42:38

Keith Smith
2020-01-10 22:18:03

Keith Smith
2020-01-10 22:19:09

Keith Smith
2020-01-10 22:21:10

John Chrapkowski
2020-01-11 11:05:18

James Ho
2020-01-11 11:13:49

James Ho
2020-01-11 11:15:15

Keith Smith
2020-01-11 21:20:44

原文網址 Rob Allison
2020-01-09 22:20:06

Question (might be silly, and sorry for the Ender 3 noise). My Photon S used to make the same exact sound when the bed raised and lowered. Now, when it lowers, it's almost silent. I've also been having a lot of failed prints, which I suspect is from switching resin brands (I've reveled, etc). Is this change in sound indicative of a problem? This isn't a question about the failed prints, more about the noise change.

翻譯年糕

Christos Boukos
2020-01-09 22:22:50

Sander van Deijl
2020-01-09 22:25:19

Rob Allison
2020-01-09 22:25:47

Rob Allison
2020-01-09 22:30:27

Christos Boukos
2020-01-09 22:49:55

Rob Allison
2020-01-09 22:51:21

Christos Boukos
2020-01-09 22:53:21

Rob Allison
2020-01-09 23:04:52

Gary Bunda
2020-01-12 15:53:01

原文網址 Rob Allison
2020-01-08 22:05:22

General question: What would cause the raft to be lifting off of the print bed?

翻譯年糕

Alejandro Rodríguez Quintero
2020-01-08 22:06:44

Rob Allison
2020-01-08 22:10:53

Sander van Deijl
2020-01-08 22:21:52

Rob Allison
2020-01-08 22:27:22

Sander van Deijl
2020-01-08 22:27:45

Rob Allison
2020-01-08 22:27:58

Alejandro Rodríguez Quintero
2020-01-08 22:28:21

Sander van Deijl
2020-01-08 22:29:20

原文網址 Rob Allison
2019-12-27 12:06:16

Just wanted to thank everyone that gave me suggestions/pointers. First successful print! Bard from Cast N Play. This group is such a great resource.

翻譯年糕

原文網址 Rob Allison
2019-12-27 03:56:36

Pretty frustrated at the moment. New Photon S, test print went ok. Failed print next (nothing happened). Emptied vat, cleaned blob off FEP, re-leveled. Printed the third picture (don't remember settings), bard comes out about half done. Went in, tweaked settings and this is what happened (first pic, settings in second pic). What am I doing wrong?

翻譯年糕

Sebasti Aan
2019-12-27 04:25:19

Rob Allison
2019-12-27 04:27:34

Kris Leon
2019-12-27 05:10:52

Kris Leon
2019-12-27 05:12:18

Kris Leon
2019-12-27 05:14:13

Rob Allison
2019-12-27 05:31:14

Kris Leon
2019-12-27 05:41:26

Gary Priest
2019-12-27 06:50:49

原文網址 Rob Allison
2019-12-25 00:22:26

Hello all! I received my Photon S yesterday, and the initial test print went well. However, I tried to print 2 minis after this after slicing them in the Anycubic software, and both failed. The printer went through the motions of printing, but no model was actually produced. I don't have the settings I used in front of me, but can anyone shine a light on the potential issue(s)? Any help is greatly appreciated. Thanks in advance!

翻譯年糕

Shane Bryant
2019-12-25 00:24:53