管理員
統計數據
原文網址 Chris Christiansen 2020-03-21 04:29:17
So I can’t get my printer to print properly, I have checked the lcd screen, I have re oriented the prints, I have re leveled the build plate, and nothing seems to work, I am using elegoo grey with 6 bottom layers at 80 seconds and 5 seconds at .02 after that, same settings I’ve always used and have worked well, all I keep getting are bits of cured resin on the screen as if I had poor bed adhesion but as I said I’ve re leveled idk how many times with the same results over different prints
Robert Jeppesen 2020-03-21 04:31:28
Try releveling closer to the screen then you think it should be.
Tom Howley 2020-03-21 04:36:10
I am using the same resin and am having success with 10 layers at 90 seconds
Chris Christiansen 2020-03-21 04:45:40
Tom Howley I’ll have to try that instead
Chris Christiansen 2020-03-21 04:46:31
Robert Jeppesen I’ve been trying closer each time but I’m always worried about messing up the screen, usually just do the paper test. I’ll try going closer though for my next print.
James Richmond 2020-03-21 04:49:03
i've heard that if your resin is too cold, it'll be difficult to get the resin to stick to the plate, try heating the plate before printing
Chris Christiansen 2020-03-21 04:55:01
like the build plate? With a lighter or something? I know that’s the case with filament I hadn’t heard that with resin, may be worth a shot ?
James Richmond 2020-03-21 04:55:17
the plate... hair dryer
Chris Christiansen 2020-03-21 04:57:07
Right I just had never heard that before as far as resin goes, I’ll try it though.
James Richmond 2020-03-21 04:59:53
https://www.reddit.com/....../ai44zw/temperature_is_key/
Chris Christiansen 2020-03-21 05:07:07
James Richmond nice thanks for the link, my resin and plate should be in those perimeters already but I’m going to heat them a bit nonetheless to see what changes!
原文網址 Chris Christiansen 2020-01-16 12:30:52
Is switching to .03 layer height from .05 for dnd miniatures worth it’s, the print times for most items double-triple, is there enough extra detail to make it worth it?
Nicholas Taylor 2020-01-16 12:39:21
Chad Elstad 2020-01-16 12:46:27
Luke Mason 2020-01-16 12:53:06
Mikko Meriläinen 2020-01-16 13:42:33
Bob Deblier 2020-01-16 20:15:22
Joseph Wright 2020-01-17 12:06:16
Chris Christiansen 2020-01-17 12:07:09
Chris Christiansen 2020-01-17 12:07:57
Joseph Wright 2020-01-17 12:22:42
Nicholas Taylor 2020-01-19 02:14:23
原文網址 Chris Christiansen 2020-01-10 23:58:59
So I got my photon about a month ago and have been printing a bit, last night as I started a print the printer moved to the vat as normal but then refused to move up or down after that, I could hear the motor running but the z axis didn’t spin or move at all, cancelled the print and still didn’t move, I shut it off and turned it back on and was able to move the z axis home, then gave it another go on a different print and the same thing happened, this is my first resin printer so I don’t know much about the tech side of it aside from the actual resin curing process so if you could be detailed if you think you know what’s up that would be great, thanks a lot.
Simon Rees 2020-01-11 00:11:24
Chris Christiansen 2020-01-11 00:12:29
Simon Rees 2020-01-11 00:14:12
討論主題
全不選 常用關鍵字
