Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Cameron Lee Johnson
2020-04-02 21:41:13

I just noticed my build plate isnt flat. But is actually pretty significantly bulging in the middle. This is causing prints to stick down the middle. But peal near the edges and cause some warping.

I know rhe build plates are never perfect, but whats the fix? I was gonna try more base layers at higher exposure but i wanted some other input

翻譯年糕

Derek Fontes
2020-04-02 21:48:27

You might be able to take it to a local machine shop and have them spotface it to make it flat.

Mi Ha
2020-04-02 21:55:58

You can machine it flat but increasing base exposure time will also work.

Richard Shapiro
2020-04-02 22:17:58

Assuming you can't return it and get them to send you another, sand it - it's hard to get it flat if the bulge is in the middle, so if it was me, I'd sand only the middle until it is just a tiny bit concave, then use sandpaper stuck down to a flat surface to get it flat from there.

Jeff Greenfield
2020-04-02 23:32:39

Best thing to do is have a machine shop fly cut the face, it could also be sanded using paper on a piece of granite or other surfaced flat natural stone, but with high in the center like yours, that’s a tough one to get out manually.

原文網址 Cameron Lee Johnson
2020-03-19 01:40:27

Am i suppose to move the build plate to the Home position before starting a print? I had it all the way up (where it moved to at the end of the last print), but it didnt move after starting. Sadly i didnt notice until now. So a little extra work to clean, but what ever.

翻譯年糕

Andrew Glover
2020-03-19 01:42:15

It should have moved on its own. Sounds like you have a mechanical issue

Grant Weaver
2020-03-19 01:43:59

Shouldn’t have to but every once in a while mine does this as well.

Peter Csaki
2020-03-19 03:50:07

Mine too. Found that turning it off and on before every print fixes it.

原文網址 Cameron Lee Johnson
2020-03-10 08:36:07

For miniature bases (the ones im looking to print are textured on top) what orientation do you find gets the best results? Im guessing the best option is either

Flat on bed
Tilted up from bed 10 or 15 degrees
Straight up on its side
Or straight up but tilted a little.

Im obviously wanting as true to shape as possible, with minimal support marks on visible parts of base.

Thoughts? There are no wrong answers

翻譯年糕

Justin Miller
2020-03-10 08:41:06

Nick Van Oort
2020-03-10 08:42:20

Jacob Hale
2020-03-10 08:46:22

Daniel Faubert
2020-03-10 08:47:28

Yessik Ziiq
2020-03-10 08:50:31

Cameron Lee Johnson
2020-03-10 09:16:26

Rantinan Winters
2020-03-10 10:35:12

Ryan Tudor
2020-03-10 10:41:23

Ryan Tudor
2020-03-10 10:41:36

Ryan Tudor
2020-03-10 10:44:09

Ryan Tudor
2020-03-10 10:45:29

Adam Scaramella
2020-03-10 19:58:49

Wes Mischke
2020-03-11 03:26:43

Stephen Hill
2020-03-11 04:11:25

Alex Muirhead
2020-03-11 04:19:53

Ryan Tudor
2020-03-11 04:28:08

Cameron Lee Johnson
2020-03-11 04:28:52

Vít Kuře Prokop
2020-03-11 05:01:25

Ryan Tudor
2020-03-11 05:14:01

Ryan Tudor
2020-03-11 05:15:07

Justin Scott Larson
2020-03-11 09:45:34

原文網址 Cameron Lee Johnson
2020-03-09 05:49:41

Its a little hard to see, but The front edge of my bottom layers/support bottoms kinda pealed away from the build plate, everything looks like its printing fine so im assuming it started happening right from the beginning and i got lucky that those supports werent needed

Is this a leveling issue?

翻譯年糕

Mark Wardle
2020-03-09 06:03:55

Cameron Lee Johnson
2020-03-09 06:05:45

原文網址 Cameron Lee Johnson
2020-03-09 01:44:17

Still trying to figuring out scaling lol. I was going for a warhammer sized figure. This is more like a dropzone commander/flames of war. He is a little messy cause im not gonna bother cleaning a model i wont use

翻譯年糕

Vilius Jonaitis
2020-03-09 01:50:41

Ryan Tudor
2020-03-09 02:08:06

Ryan Tudor
2020-03-09 02:08:56

原文網址 Cameron Lee Johnson
2020-03-07 14:31:06

So i had my first failure. I was printing a large piece of a display model (a little smaller than a baseball) and then super tiny versions of that model as well.

They all broke off the supports. Since this was my first time using opaque resin, im assuming its under exposure? Or would the supports have failed as well? What interesting is i had 2 sets of the smaller model pieces. You can see the base layers of one on the plate there. But the other has nothing

Anycubic black
4 base layers at 75 seconds.
.05 layer height at 8 seconds

翻譯年糕

Scott Pavlich
2020-03-07 15:09:32

Jesper Hvid
2020-03-07 15:47:22

原文網址 Cameron Lee Johnson
2020-03-07 05:01:55

I know there are a ton of factors for itx but im about to use my first "non translucent" resin and was wondering what a good exposure to start with. Im sure Many adjustment will be made along the way, but would you say start at 8 seconds? 2 seconds? ???

.05 layer height

翻譯年糕

Grant Weaver
2020-03-07 05:05:32

Bob Deblier
2020-03-07 05:14:59

Scott Pavlich
2020-03-07 05:23:30

Cameron Lee Johnson
2020-03-07 06:02:27

原文網址 Cameron Lee Johnson
2020-02-18 23:43:54

Looking for opinions because this is a weird situation.

Order my photon, 2 bottles of extra resin, not including the one that comes with printer, and a pack of fep sheets from anycubic. About a month later i got the printer (delays due to new year and virus. Expected and understandable). But It has been 8 days now and still no extra resin or fep sheets.

Should i give them some more time or send a quick message to check the status of it?

They have a lot on their plate so i dont wanna add more to it if i dont need to. Thoughts?

翻譯年糕

Cash Lo
2020-02-18 23:46:32

Wes Mischke
2020-02-18 23:53:44

Jason Hartloff
2020-02-19 01:00:40

原文網址 Cameron Lee Johnson
2020-02-12 23:52:11

Finished the base for a spider man i am going to print. I didnt hollow it. So this thing is a beast.

Had a scare mid print where some supports on a wing failed. But after a few layers it fixed itself. After some minor green stuff work you wont even be able to tell.

翻譯年糕