Anycubic Photon Printer Owners 造訪社團

原文網址 Kris McEwan
2019-12-13 01:09:44

First Test print with the printer went OK. Using EleGoo Transparent red.
Post processing i think was done right however one thing is How long do i need for UV? is there a rule of thumb or just a guess?

翻譯年糕

Paul West
2019-12-13 01:13:58

Kris McEwan
2019-12-13 01:16:12

Paul West
2019-12-13 01:19:50

Jarin Udom
2019-12-13 14:39:03

Paul West
2019-12-13 20:34:29

原文網址 Neil Ramsay
2019-12-13 00:41:43

Haven't been printing much lately, because my heater's dead in the box, and it's been very COLD in the room the printers are in (dropping into the mid to low teens Celsius). Fired up a print on Siraya Blu/Tenacious mix just to see if it would print or fail (expected a fail in this cold). Worked like a charm. Printed out two police badge props for a play coming up next month.

For a super-inexpensive printer, this thing is quite the workhorse.

翻譯年糕

Scott Schwoppe
2019-12-13 03:21:36

Tristram Chapman
2019-12-13 03:29:50

Neil Ramsay
2019-12-13 03:51:42

Scott Schwoppe
2019-12-13 04:08:51

Neil Ramsay
2019-12-13 04:22:06

原文網址 Alexx Butnotalex
2019-12-13 00:26:17

Has anyone tried mixing the anycubic clear green and elegoo grey?

翻譯年糕

原文網址 John Ray-Wray
2019-12-13 00:12:40

pk guys I have noticed this happening a few time with "square" items where its slanting.. what am I doing wrong? you can see at the top where the base is.

翻譯年糕

Ty Mansfield
2019-12-13 00:16:01

John Ray-Wray
2019-12-13 00:16:34

Ty Mansfield
2019-12-13 00:17:21

Michel Bondo Hansen
2019-12-13 00:18:21

Jared Zadorozny
2019-12-13 03:23:57

William Riker
2019-12-13 03:52:52

原文網址 Jason E Heuer
2019-12-13 00:06:25

So I lucked out. One of the printers at work was getting upgraded so the equipment tower was getting trashed. Found a great home for my printer and I added two large carbon air filters to the fans in the back and no more smell.

翻譯年糕

Kevin Whiteside
2019-12-13 00:09:00

Sargon Smith
2019-12-13 00:24:22

Pierre Gallois
2019-12-13 14:47:42

原文網址 Dave Green
2019-12-12 23:49:38

Anybody got a tried and tested 0.02 layer time for Elegoo ABS Grey?

翻譯年糕

Will Koehler
2019-12-13 00:09:16

Joe Brislane
2019-12-13 12:10:14

原文網址 Dyllon Baldock
2019-12-12 23:44:57

Hey guys rookie printer here, my first printer photon S rocking next week looking for a chariot pulled by an elephant STI for dnd size
Thanks in advance

翻譯年糕

Joe Comedian
2019-12-12 23:48:01

Dyllon Baldock
2019-12-12 23:51:59

原文網址 Philip Schifano
2019-12-12 23:11:18

Is there any way to covert a .photon file to STL? I spent hours trying to fix a sliced photon file in validator and finally got it good and now I need to move it a few mm on the build plate- when I try to open it in chitubox it gives me the "file is too large" error. I don't want to start from scratch again....

翻譯年糕

Smith Hayward
2019-12-12 23:33:12

原文網址 James Tanner
2019-12-12 22:42:14

Got a new Photon S yesterday and got it set up next to my existing original Photon. Both printers will be cranking out D&D minis in bulk for Imgur Secret Santa.

I'm impressed with the onboard filtration of the S so far. It's only slightly worse than my original photon which has been upgraded with a complete air extraction system.

翻譯年糕