Anycubic Photon Printer Owners 造訪社團

原文網址 Will Koehler
2019-11-05 04:58:11

Ok Photonsters I need some brain power. My problem is that I am getting some cured resin on my FEP after prints, in patterns/spots that don't make a whole lot of sense to me. The prints are coming out fine with no failures, I just get left with a goo/cured resin on my FEP. Here is what I've done in my troubleshooting.....

1) New USB

2) New FEP

3) New LCD

4) Re-level

5) Flashed Epax firmware that is supposed to combat frame shearing

6) Run my files through the validator to correct any missed islands

These are files and prints I've printed in the past without issue, so that leads me to believe it is happening between my computer and the machine. I use Elegoo Grey and 8 base layers @60 and normal layers @11. Again, these are settings I've used fine for months and months and based off the resin exposure test I did here. I'm open to suggestions here, I'm pretty stumped and think I've gone through all the appropriate checks here.

翻譯年糕

Vlad Trofimovskiy
2019-11-05 14:22:33

Nicholas Taylor
2019-11-06 04:21:35

Will Koehler
2019-11-06 04:23:40

原文網址 Kurt Camaro
2019-11-05 04:23:28

Testprints of my latest 3D-Scans, scaled to 1:87, as always :-)

翻譯年糕

Kevin Boogaard
2019-11-05 04:34:09

Kurt Camaro
2019-11-05 05:31:30

Kevin Boogaard
2019-11-05 05:33:40

Kurt Camaro
2019-11-05 05:49:17

Otto Rey
2019-11-06 11:15:06

原文網址 Jason Male
2019-11-05 04:16:10

Hi all thanks for the add. My photon s should arrive anytime.. it's intended use is for tabletop gaming minis. Are there good videos for setup, slicing etc that I should watch before I start?

翻譯年糕

Jason Male
2019-11-05 04:16:45

Victor Clinton Dieter Eichhorn
2019-11-05 04:24:05

Joe Spacco
2019-11-05 04:25:27

原文網址 Chris Graf
2019-11-05 04:00:16

Photon Converter v2

.photons, .photon, .pws, .cbddlp, AA support Photon Converter v2

.photons, .photon, .pws, .cbddlp, AA support 翻譯年糕

Chris Graf
2019-11-05 04:01:20

Chris Graf
2019-11-05 04:06:40

Marcus Weseloh
2019-11-05 04:36:41

Angongar Jalbor
2019-11-05 04:46:17

Lucas Neñer
2019-11-05 04:54:33

Chris Graf
2019-11-05 05:01:24

Chris Graf
2019-11-05 05:04:50

Vinicius Silva
2019-11-05 05:04:57

Jarrod Smith
2019-11-05 05:43:47

Uriah Redden
2019-12-30 03:19:10

原文網址 Jamie Ott
2019-11-05 03:59:58

Another finished print.

翻譯年糕

Guy Romhild
2019-11-05 05:13:44

Jamie Ott
2019-11-05 05:16:49

Guy Romhild
2019-11-05 05:17:17

Mikko Asikainen
2019-11-05 14:51:12

Ian Chess
2019-11-05 16:19:57

Jamie Ott
2019-11-05 22:54:49

原文網址 Artur Fuste
2019-11-05 03:54:58

Today I've updated our Photon and Photon S Resin Settings Spreadsheets. 翻譯年糕

Artur Fuste
2019-11-05 04:51:37

Artur Fuste
2019-11-05 05:21:42

原文網址 Mihai Dragomir
2019-11-05 03:47:22

So now that it's official, and the new photon will have/has the same motherboard as the photon S, will this mean that a screen replacement will require the S- model of screens?

Also, has anyone using the new photons (with proprietary mb) replace their screen? and if so, what screen did you use?

翻譯年糕

原文網址 Maxime Mathurin
2019-11-05 03:46:01

Hey guys

I have been running for a couple of months and had a couple of problèmes, which needed that I flash the firmware a couple of Time: z not Working , fan not Working and the uv light ( LCD screen ) Who begin to flicker like crazy at some point.
That last bug, the flickering, happened like 2 Times on the last weekend. I flashed yesterday and everything got back to normal. One successful print, and then another fail print with flickering problem this morning.

Does somebody has an Idea of what is happening? Anycubic support didnt offered any other suggestion than to flash the firmware last month when I reached put...
Thanks !

翻譯年糕

Paul West
2019-11-05 03:53:30