Anycubic Photon Printer Owners 造訪社團

原文網址 Kent Dustin Navarette
2019-10-23 14:18:16

why does it not make the right format for the file. it only does this unrecognized file in my chitubox slicer? need help asap

翻譯年糕

Jeff Slaughter
2019-10-23 14:37:24

Kent Dustin Navarette
2019-10-23 14:39:11

原文網址 Rob McEwen
2019-10-23 14:09:30

Have i got dead pixels? Both of these were printed on the same build plate at the same time... :(

翻譯年糕

Mark Wardle
2019-10-23 14:18:22

Rob McEwen
2019-10-23 14:19:43

Dave Fishpig
2019-10-23 14:22:23

Maksim Andreyavich Belous
2019-10-23 14:44:11

原文網址 Anthony Tapp
2019-10-23 13:39:22

Ok so is there a way to straighten prints? Like something I can add to the resin to make it either flexible (preferably) or just less brittle. Because I just printed something that is small with thin pieces and it was flexible right off the printer. So I thought that if I primed it right away with out curing it that it would stay flexible unlike the test piece that fell apart after I cured it. However a few hours afterwards i was seeing if it was still flexible and it snapped super easily with little presser. I thought that the gray primmer would stop it from curing and it wasn’t even in sunlight at all. Does anyone have any suggestions as to what could have happened and how I might stop this from happening again? I should also mention that it was in a 42* cooler for 6 hours at work and I also suspect that they use clear uv lighting in there but I am unsure.

翻譯年糕

Dan Jay
2019-10-23 13:44:26

Justin Lincoln
2019-10-23 13:47:53

Sam Davey
2019-10-23 13:58:10

Dane Bennett
2019-10-23 14:02:46

Anthony Tapp
2019-10-23 14:04:47

Aaron Strome
2019-10-23 14:09:50

Anthony Tapp
2019-10-23 14:45:01

原文網址 Robert Small
2019-10-23 12:04:21

I can't seem to print anymore without completely filling up the build plate. Anyone else?

翻譯年糕

Tim Moulton
2019-10-23 12:08:05

Jessie Shoshone
2019-10-23 12:09:25

Robert Small
2019-10-23 12:14:50

Tim Moulton
2019-10-23 12:15:15

John Chrapkowski
2019-10-23 12:18:33

Stefan Ritchie
2019-10-23 17:43:36

原文網址 Gordon Scherer
2019-10-23 11:48:47

Thoughts on why the circled ones wouldn’t print?
The rafts and supports printed for them but they’re just little puddles stuck on the FEP.
All the rest are fine.

Also, pity the people playing in the Xmas D&D adventure I’m going to run.

翻譯年糕

Simon Wilson
2019-10-23 11:54:57

Gordon Scherer
2019-10-23 11:57:14

Tim Moulton
2019-10-23 11:57:20

Louis Siciliano
2019-10-23 12:46:03

原文網址 Shivanand Chanderbally
2019-10-23 11:42:09

Hope you guys are having a great day! Here's my latest video. Hope you like it and it helps someone! ?

翻譯年糕

Simon Wilson
2019-10-23 12:35:32

原文網址 Damien Jones
2019-10-23 11:27:30

First ever print done and dusted. Now the fun part.

翻譯年糕

Fifa Mia
2019-10-23 11:56:05

原文網址 Ruben Haris Lukito
2019-10-23 11:16:55

What does dental castable mainly used for?

翻譯年糕

Mike Michaels
2019-10-23 11:19:15

Humphrey Ho
2019-10-23 11:25:33

Ruben Haris Lukito
2019-10-23 11:46:14

Ruben Haris Lukito
2019-10-23 11:46:45

Humphrey Ho
2019-10-23 11:47:06

Mikko Meriläinen
2019-10-23 13:09:34

Nipuna Gunarathne
2019-10-23 13:57:47

原文網址 Jay Jones
2019-10-23 11:08:27

The Photon produced some more bullet-tip wires w/ tires.

翻譯年糕

Ricardo Pedro
2019-10-23 15:15:01

Jay Jones
2019-10-23 16:15:19

Ricardo Pedro
2019-10-23 16:17:55

Jay Jones
2019-10-23 16:19:04

Ricardo Pedro
2019-10-23 16:22:34

Jay Jones
2019-10-23 16:26:03

Janne Sjöström
2019-10-23 21:03:45

Ricardo Pedro
2019-10-23 21:07:33

Janne Sjöström
2019-10-23 21:10:07

Janne Sjöström
2019-10-23 21:15:26

Polly Jackson
2019-10-24 01:19:58

Polly Jackson
2019-10-24 01:20:16

Polly Jackson
2019-10-24 01:20:47

Ricardo Pedro
2019-10-24 01:45:07

Janne Sjöström
2019-10-24 02:01:31

Jay Jones
2019-10-24 11:12:33

Chris Casarez
2019-10-25 03:55:58

Jay Jones
2019-10-25 04:11:55

Chris Casarez
2019-10-25 05:07:24

Benjamin Oppenheimer
2019-10-25 11:15:19

Polly Jackson
2019-10-26 06:44:09

Polly Jackson
2019-10-26 06:45:43

原文網址 Nick Wichert
2019-10-23 11:03:20

I have no experience with painting prints from the Photon so I'm looking for some advice on how to get started and what might be the best paint to use, particularly for an outdoor application. Also, do you sand the prints before paint?

翻譯年糕

Dane Bennett
2019-10-23 11:07:37

討論主題

發文排行榜

回文排行榜

熱門關鍵字