Anycubic Photon Printer Owners 造訪社團

原文網址 Dean Eyre
2019-09-22 10:50:30

Any idea what happened here. I know the parts are lifting from the build plate but if you look at the ends they look as if they sank into support raft

翻譯年糕

Adrian Carter
2019-09-22 10:55:59

Scott Pavlich
2019-09-22 11:45:35

Dean Eyre
2019-09-22 16:02:05

Milton Maxson
2019-09-22 19:54:29

Dean Eyre
2019-09-24 20:36:54

Dean Eyre
2019-09-25 08:12:40

Milton Maxson
2019-09-25 10:39:13

Dean Eyre
2019-09-25 14:10:48

原文網址 Béla Tibor Király
2019-09-22 10:46:30

Thank you for the reception.

謝謝你的接待.

· 查看原文 · 為此翻譯評分

原文網址 John Leonard
2019-09-22 10:42:51

My dice problem is getting weirder. So my last test, i went overboard with supports and up'd my exposure by a second. But what ive just noticed is that the discortion that im getting on the cube is BELOW the support line and the stuff above it, is FINE! What is going on here guys?

翻譯年糕

Pascal Posada
2019-09-22 10:57:58

John Leonard
2019-09-22 11:02:22

Jared Zadorozny
2019-09-22 11:08:09

John Leonard
2019-09-22 11:11:01

Pascal Posada
2019-09-22 11:18:30

John Leonard
2019-09-22 11:19:31

Julia von Pfaler
2019-09-22 15:17:33

John Leonard
2019-09-22 16:21:24

原文網址 Lee Baxter
2019-09-22 10:35:35

I dont understand this part. hoping someone can help. After adding supports to what i want. Do i open it in the validator BEFORE slicing? i have been slicing then opening it in photon validator then coming back to adjust and it wont open the file to adjust supports. tia

翻譯年糕

Adam Burch
2019-09-22 10:38:12

Lee Baxter
2019-09-22 10:48:11

Lee Baxter
2019-09-22 10:48:36

Scott Pavlich
2019-09-22 11:07:09

Lee Baxter
2019-09-22 11:16:42

Ian Gill
2019-09-22 16:00:24

Lee Baxter
2019-09-22 16:03:27

Lee Baxter
2019-09-23 11:22:50

谢信福
2019-09-23 20:19:55

原文網址 Charles Kellner
2019-09-22 10:25:24

First print, I think it turned out amazing. Only thing is I think that it's a bit on the small side. When I got the file it was larger than 28mm so I changed the z to 28mm. Is that what made it smaller by chance? Does anyone have advice on resizing

翻譯年糕

Stefan J Simons
2019-09-22 10:29:11

Francis X Benz
2019-09-22 10:31:05

Charles Kellner
2019-09-22 10:31:55

Jeremy Kackley
2019-09-22 10:37:17

Jon Vogel
2019-09-22 10:37:34

Jeremy Kackley
2019-09-22 10:44:32

Rory Kostman
2019-09-22 10:57:30

Francis X Benz
2019-09-22 21:28:10

Matt Hooton
2019-09-26 05:32:15

原文網址 Shivanand Chanderbally
2019-09-22 10:16:28

My latest vid. I really enjoy making them. Hope you guys like them. Happy Printing!

翻譯年糕

Elle Heilig
2019-09-22 10:59:26

Shivanand Chanderbally
2019-09-22 11:04:55

原文網址 James Byberg
2019-09-22 10:05:09

Upgraded the firmware to the 4.2.18 version, releveled per instructions, and this was the result... sigh. Back to the drawing board again.... ?

翻譯年糕

Rory Kostman
2019-09-22 11:03:53

James Byberg
2019-09-22 11:06:33

原文網址 Jim Wolfe
2019-09-22 09:39:29

Hey All, I just did a bigger print of a mini (x225%) and i have a few hole going directly thru my print. Has this happened to any one and what might have caused it. I did a full clean of the Vat before i ran this print.

翻譯年糕

Elle Heilig
2019-09-22 09:40:59

Elle Heilig
2019-09-22 09:41:30

Tiernan Messmer
2019-09-22 09:43:31

Jim Wolfe
2019-09-22 09:44:04

Jim Wolfe
2019-09-22 09:44:47

Elle Heilig
2019-09-22 09:47:20

Jim Wolfe
2019-09-22 09:49:15

Tiernan Messmer
2019-09-22 09:51:24

Jim Wolfe
2019-09-22 09:53:40

Phil Davidson
2019-09-22 10:37:36

Ben Cox
2019-09-22 11:01:06

Elle Heilig
2019-09-22 11:04:27

James Munsterman
2019-09-22 11:15:38

James Munsterman
2019-09-22 11:16:14

Stephen Lewis
2019-09-22 13:50:18

Jim Wolfe
2019-09-23 05:53:54

Susan Sioux Mercer
2019-09-23 07:41:32

Jim Wolfe
2019-09-23 07:42:28

原文網址 Brian Alexander
2019-09-22 09:07:39

I have a question about Elegoo Grey resin: is it supposed to have a... for lack of better word... sticky surface even after cleaning and curing? The print quality is nice but the surface doesn't quite feel solid. It doesn't mark. So it is solid but doesn't feel quite solid. Is this normal?

翻譯年糕