• 3D列印服務
  • #maker+t=market
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Rory Kostman
2020-03-13 07:18:16

I need to add some flexibility to some hinge covers for Dell Chromebooks. The existing covers break very easily out of ABS (the small locking tabs, not the entire cover). What additive should I add to a typical resin to retain hardness like injection molded part, but add some flexibility to help those small bits from breaking? Suggestions appreciates

翻譯年糕

Dani Martinez
2020-03-14 19:54:36


原文網址 Rory Kostman
2020-03-12 22:41:10

Anyone else having a problem with the SMELL of IPA mixed with resin? It is super "sweet" and makes me a bit queasy. The RESIN smell itself doesn't bother me, but the smell of used IPA does. Plus I spilled a bit with a funnel accident trying to strain out cured resin bits from the IPA. I may have to toss all my containers, and keep clean that room to get rid of the smell.

翻譯年糕

Bob Deblier
2020-03-12 22:45:43

Steve Ludwig
2020-03-13 01:36:44

Steve Ludwig
2020-03-13 01:37:24


原文網址 Rory Kostman
2020-01-16 23:49:14

I've been using the Photon File Validator for a couple of months to auto-fix islands where it can. I *JUST* realized two nights ago that I can step through the layers with islands and fix them... DOH!!! That was not obvious from the UI. I should have read the manual

翻譯年糕

Kyle McPherson
2020-01-17 00:14:53

Gunnar Hannich
2020-01-17 00:49:40

Mike Tate
2020-01-17 01:25:59

Shawn McDonald
2020-01-17 01:37:35

Shawn McDonald
2020-01-17 01:40:34

Rory Kostman
2020-01-17 03:04:40

David Brighton
2020-01-17 04:17:19

Gunnar Hannich
2020-01-17 05:01:06

Gunnar Hannich
2020-01-17 05:04:27

Gunnar Hannich
2020-01-17 05:13:27


原文網址 Rory Kostman
2020-01-15 23:27:21

Why would a few prints recently be successful, but have a vertical line running through the part, from the plate to the top. one side of the line, the entire model is shifted "forward" by a fraction of a mm. nothing failed. Supports all fine, no sags. The next print, large plates full of battletech mech parts, no issues. It looks like the model itself was planecut, offset .5mm and re-assembled. I will post photos as necessary. Twice in the past half dozen prints, I have had this issue. It has been minor enough that I can correct it with some filing/sandpaper.

翻譯年糕

Herman Simpson
2020-01-15 23:46:15

Rory Kostman
2020-01-15 23:52:10

Herman Simpson
2020-01-15 23:52:46

Rory Kostman
2020-01-15 23:54:37

Rory Kostman
2020-01-16 07:36:06

Rory Kostman
2020-01-16 07:38:46

Rory Kostman
2020-01-16 08:09:39

Herman Simpson
2020-01-16 19:32:57

Rory Kostman
2020-01-16 20:42:17

Herman Simpson
2020-01-16 22:35:05

Rory Kostman
2020-01-16 23:35:22

Herman Simpson
2020-01-16 23:40:32

Herman Simpson
2020-01-16 23:41:08

Rory Kostman
2020-01-16 23:46:42


原文網址 Rory Kostman
2020-01-15 23:24:31

Are there any well-written instructions on the exposure test print? I've read some a few times and it was written by someone who doesn't write documentation for a living. I have always sorta "winged it" with my exposures and I've been happy with the results but that nagging feeling where "could it be better?"

翻譯年糕

Bob Deblier
2020-01-16 00:06:36

Zena Andreou
2020-01-16 00:09:31

Gunnar Hannich
2020-01-16 00:40:07


原文網址 Rory Kostman
2019-09-10 06:47:33

Tramming to both the bottom plate, per instructions, and to the FEP film per YouTube, this photo shows what my build plate angle between plate and mount looks like. Is it a case of "don't worry about what it looks like if it prints ok"? Or should I contact AnyCubic since the printer is 2 weeks old?

翻譯年糕

Stefan Lukus
2019-09-10 06:53:21

Simon Wilson
2019-09-10 07:02:27

Mike McCreery
2019-09-10 07:35:22


原文網址 Rory Kostman
2019-09-06 06:27:42

Tram to the panel, or tram to the FEP? My tram doesn't Look level, but print jobs are ok. I trammed to the build plate per instructions

翻譯年糕


原文網址 Rory Kostman
2019-09-06 05:05:42

Thanks for the group. I've done FDM for about 5 months and just bought a Photon. So far, the first few prints have been great. looking forward to expanding my Photon knowledge.

翻譯年糕

Chad Elstad
2019-09-06 05:14:58

Rory Kostman
2019-09-06 08:04:38

이재열
2019-09-07 10:18:03


 

討論主題

全不選 常用關鍵字