Anycubic Photon Printer Owners 造訪社團

原文網址 Aaron Marino-Drake
2019-07-24 12:41:56

Our Photon came in the mail today! Got it setup, hopefully leveled correctly. Testing a print now!

ANYCUBIC
2019-07-24 14:05:10

原文網址 Vinay Shah
2019-07-24 11:56:47

So is there any alternate slicing software that I can use for the photon S instead of the one that comes with it? And are there any primary tests that you guys think I should do before starting full fledged printing?

翻譯年糕

Robert Silvers
2019-07-24 12:05:03

Vinay Shah
2019-07-24 12:05:54

Robert Silvers
2019-07-24 12:07:18

Vinay Shah
2019-07-24 12:07:30

原文網址 Lee Rich
2019-07-24 11:25:23

Are there any websites that sell aftermarket Photon parts?

翻譯年糕

Mike Fatchett
2019-07-24 12:48:17

Lee Rich
2019-07-24 14:02:36

原文網址 Kallon Fernandez-Tripp
2019-07-24 10:59:35

Hey guys first attempted print on the test cube 30% of the way through nothing is on the base plate. I checked the resin vat and it's free of any hardened resin and I checked the uv light and it seems to be working any ideas on what could have gone wrong? I'm using anycubic green resin

翻譯年糕

Stefan Giudici
2019-07-24 11:40:02

Kallon Fernandez-Tripp
2019-07-24 11:49:52

Brian Wright
2019-07-24 11:51:07

Kallon Fernandez-Tripp
2019-07-24 11:55:21

Brian Wright
2019-07-24 11:57:58

Kallon Fernandez-Tripp
2019-07-24 11:58:46

Kallon Fernandez-Tripp
2019-07-24 11:59:56

Kallon Fernandez-Tripp
2019-07-24 12:00:06

原文網址 Kris Occur
2019-07-24 10:59:34

Newb question but I primarily print D&D minis for my party in elegoo grey. Once they’re washed and cured (by UV LED or sun), are they good to be handled and used on the table top assuming I do -NOT- paint them? Or do I need to seal them? If so, what do I need to use?

I primarily use this grey resin because I don’t want to paint them. But now I’m wondering if they have to be sealed.

翻譯年糕

Dave Smith
2019-07-24 11:05:02

Dave Smith
2019-07-24 11:06:57

Paul West
2019-07-24 11:09:42

Chad Elstad
2019-07-24 11:19:11

Kris Occur
2019-07-24 18:17:10

Kris Occur
2019-07-24 18:22:45

James O'Keane
2019-07-24 20:39:11

Eivind Husby
2019-07-24 20:53:46

Eivind Husby
2019-07-24 20:54:19

Kris Occur
2019-07-24 22:54:12

Kris Occur
2019-07-24 22:55:25

Eivind Husby
2019-07-24 23:03:41

原文網址 Chayanin Somton
2019-07-24 10:45:20

Anycubic grey wit 2 layers of primer, there's still a tinyyyyyyy bit of pixels visible so not sure if I should lightly sand it(lazy) or spray a couple more layers of primer to fill it(but will they lose facial details?) The heads are ~4.5cm with headcap on

翻譯年糕

Can Canino
2019-07-24 16:18:34

Carlos Aguilar
2019-07-25 07:00:27

原文網址 Joe Gomez
2019-07-24 10:36:28

Drilled out the bottom exhaust plate so it runs COOLER. Photon S

翻譯年糕

Michael Cargile
2019-07-24 11:56:25

Alex Rallis
2019-07-24 21:16:23

Joe Gomez
2019-07-24 22:29:17

原文網址 Winup McModels
2019-07-24 09:33:05

Thanks for the tips I received here, finally finished two complete 1/6 garage kits printing. Also grateful for the shares stl files.

翻譯年糕

Kyle Standring
2019-07-24 10:18:54

原文網址 Nick Williams
2019-07-24 09:27:35

Always so close to overfilling.

翻譯年糕

Chasen Harris
2019-07-24 09:33:41

Thanh M. Vu
2019-07-24 10:24:01

Nick Williams
2019-07-24 11:08:01

Susan Sioux Mercer
2019-07-24 11:13:13

Thanh M. Vu
2019-07-24 11:28:59

Nick Williams
2019-07-24 11:32:46

Nick Williams
2019-07-24 11:33:04

原文網址 Siva-Jack Sernvongsat
2019-07-24 09:24:06

I'm trying to figure out if this is a printer error or resin going bad error. I'm using Siraya Tech Blu and everything has been going fine until last week.

The Skate is a lot thinner than normal. The resin is coming out green. Supports are falling off the Skate. Ive realigned the z 3 times now and the skate doesnt even print evenly on the bed anymore.

Help

翻譯年糕

Chasen Harris
2019-07-24 09:25:19

Siva-Jack Sernvongsat
2019-07-24 09:26:39

Chasen Harris
2019-07-24 09:33:17

Mike Fatchett
2019-07-24 09:42:01

Mark Wardle
2019-07-24 10:43:18

Siva-Jack Sernvongsat
2019-07-25 07:06:34

討論主題

發文排行榜

回文排行榜

熱門關鍵字