Anycubic Photon Printer Owners 造訪社團

原文網址 Jared Rutledge
2019-07-02 11:06:53

12 Sec exposure for AC black too long 0.04? The spread sheet said 8 Sec

Stefan Giudici
2019-07-02 13:54:08

原文網址 Jared Rutledge
2019-07-02 11:03:58

Ok, I am getting a shiny, melted/deformed part on prints after curing. I am just curing for 2 min 30 sec is this too long?

翻譯年糕

Chris Rees
2019-07-02 11:07:55

Jared Rutledge
2019-07-02 11:08:24

Jared Rutledge
2019-07-02 11:08:47

Chad Elstad
2019-07-02 11:34:32

Jared Rutledge
2019-07-02 11:48:19

原文網址 Zach Sawyer
2019-07-02 10:43:32

Need some help, trying to get my photon setup and when I get to Zero Z axis this pops up. Tried the test print and it stuck to the FEP, anyone else had this problem?

翻譯年糕

Richard Shapiro
2019-07-02 11:14:30

Zach Sawyer
2019-07-02 11:26:38

Reggie Grahita Adhyatmaka Djatni
2019-07-02 13:57:03

Zach Sawyer
2019-07-03 01:24:04

Vinicius Silva
2019-07-03 01:39:26

Vinicius Silva
2019-07-03 01:39:45

Vinicius Silva
2019-07-03 01:40:51

Reggie Grahita Adhyatmaka Djatni
2019-07-03 12:19:26

原文網址 Jared Rutledge
2019-07-02 10:17:02

I have a little bit in my vat of elegoo grey and I am out of Elegoo grey now. Can I mix in a little AC grey so I don't waste the elegoo I have in there?

翻譯年糕

Dave Smith
2019-07-02 10:18:13

Jared Rutledge
2019-07-02 10:19:07

Bob Deblier
2019-07-02 13:19:40

Susan Sioux Mercer
2019-07-02 16:25:40

原文網址 Jorge Zaragoza
2019-07-02 10:05:57

Does any one know why some of my prints are Matt after curing and some are smooth and shiny? Does any one know why some of my prints are Matt after curing and some are smooth and shiny? 翻譯年糕

Joules McFarland
2019-07-02 10:08:15

Jorge Zaragoza
2019-07-02 10:18:52

Jorge Zaragoza
2019-07-02 10:19:09

Joules McFarland
2019-07-02 10:25:26

Joules McFarland
2019-07-02 10:26:48

Jorge Zaragoza
2019-07-02 10:45:20

Joules McFarland
2019-07-02 10:47:34

Jorge Zaragoza
2019-07-02 10:49:30

Joules McFarland
2019-07-02 10:50:36

原文網址 Peter Lynn
2019-07-02 08:56:19

Hi guys where can I purchase a heater setup for the photon to monitor and heat up temps accordingly. Cheers thanks.

翻譯年糕

Chris Wilander
2019-07-02 09:04:58

原文網址 Edison Ckw
2019-07-02 08:46:06

Any ideas what's the causes of these. z axis not moving,even set to home. UV test seems was bugged as you can see from the video 0.08, the screen not fully unmask. ?

翻譯年糕