Anycubic Photon Printer Owners 造訪社團

原文網址 Juan Antonio Parrilla
2019-06-16 01:48:08

Maybe I can Call this the 1st Successful print !! I used Anycubic Skin Resin. Thanks to everyone that helped !! Still need to clean the supports. 28mm

翻譯年糕

Eric Simmons
2019-06-19 19:21:38

Juan Antonio Parrilla
2019-06-20 02:57:29

原文網址 Drew Cski
2019-06-16 01:40:19

Had to turn the bottom exposure time up to 240 for the first 8 layers for it to even stick. Using anycubic photon green.

翻譯年糕

Tim Moulton
2019-06-16 01:45:22

Adam Horton
2019-06-16 01:46:53

Craig Burrows
2019-06-16 01:47:43

Chad Elstad
2019-06-16 01:50:38

Dibbs Dibblethwaite
2019-06-16 02:05:18

Drew Cski
2019-06-16 02:14:20

Drew Cski
2019-06-16 02:26:48

Drew Cski
2019-06-16 02:26:54

Dibbs Dibblethwaite
2019-06-16 02:51:27

Drew Cski
2019-06-16 03:00:24

Jay Sharp
2019-06-16 07:41:28

Drew Cski
2019-06-16 07:42:20

Stephen Farrell
2019-06-16 12:30:13

Spike Walker
2019-06-16 14:48:57

Drew Cski
2019-06-16 14:50:33

Spike Walker
2019-06-16 14:51:18

Drew Cski
2019-06-16 14:53:16

Spike Walker
2019-06-16 14:54:10

Drew Cski
2019-06-16 14:56:22

Jim Brown
2019-06-16 15:01:29

原文網址 Brian Harrison
2019-06-16 01:20:18

My prints are beginning to get covered in jelly like artifacts. They are fairly easy to remove and don’t cause the prints to fail, is this caused perhaps by overexposure? Or is it more likely an LCD issue? If you notice it seems to be a rectangle shape starting just about dead middle of the print

翻譯年糕

Dennis Tomson
2019-06-16 01:37:22

Brian Harrison
2019-06-16 01:39:25

Dave Smith
2019-06-16 01:42:45

Brian Harrison
2019-06-16 01:45:31

Jarrod Smith
2019-06-16 01:45:45

Dan Smith
2019-06-16 07:23:32

Brian Harrison
2019-06-16 07:36:02

Robert Mun
2019-06-16 11:55:09

Brian Harrison
2019-06-16 11:55:55

原文網址 Alex Clarke
2019-06-16 00:50:32

3d printed a frostgrave warband. Preeeetty happy with the results.

翻譯年糕

原文網址 Scott Simoneau
2019-06-16 00:43:54

I’d like to add some kind of heating to my printer so I can use the Siraya resins better. I’ve seen all sorts of great mods, but they all involve wiring, drilling, and other skills that I’m quite prepared to use.

Has anyone had success with a “plug and play” option? I’m envisioning maybe like a reptile heater, or some kind of small thing I can just stick in the corner behind the vat?

翻譯年糕

Chad Elstad
2019-06-16 01:08:13

Richard Shapiro
2019-06-16 01:22:34

Tom Smith
2019-06-16 02:17:48

Gary Houser
2019-06-18 01:15:55

原文網址 Kevin Dumont-Vuillet
2019-06-16 00:14:32

Hi there, I'm new to 3D printer community and already have a question, I've installed and launched the software from the USB and now want to see the test file, it didn't showed on the grid of the software but the LCD viewer seems good, any idea? Is there a specific way to load that file that I didn't get? Thanks for reading!

翻譯年糕

Benedek József Tasi
2019-06-16 00:18:50

Kevin Dumont-Vuillet
2019-06-16 00:32:35

Kevin Dumont-Vuillet
2019-06-16 00:35:07

Benedek József Tasi
2019-06-16 00:56:49

Benedek József Tasi
2019-06-16 00:59:43

Kevin Dumont-Vuillet
2019-06-16 01:06:47

Benedek József Tasi
2019-06-16 01:07:23

Stefan Giudici
2019-06-16 02:42:19

Kevin Dumont-Vuillet
2019-06-16 02:52:39

原文網址 Angus Davidson
2019-06-16 00:14:30

If I want to print something 'quickly' - draft - how thick can I go on one layer? (Using anycubic grey) 0.2 and increase the exposure time?

翻譯年糕

Scott Pavlich
2019-06-16 00:46:03

原文網址 Dylan Drummond
2019-06-16 00:10:47

Are there any Australian members on here?
I have an STL file i would like if someone could try and print for me to see if it will work. The item is some small wheel centres for a model car. Cheers

翻譯年糕

Michael Drew
2019-06-16 06:10:57

Nathan Grubb
2019-06-16 06:47:46

Greg Chapman
2019-06-16 07:29:31

Garth McKenzie
2019-06-16 09:04:43

Dylan Drummond
2019-06-16 11:02:05

Nathan Grubb
2019-06-16 11:13:01

Dale Blackwell
2019-06-16 11:15:55

原文網址 Samuel Herrera
2019-06-15 23:39:26

Photon and cr-10s pro, Putting in work. Now its my turn lol

翻譯年糕

原文網址 Andrea Giatti
2019-06-15 23:33:41

I have just received the Anycubic Photon and printed the demo on the stick using orange instead of green resin. Some of the lines are not straight and part of the grid is deformed upwards. Also, while printing the object was like oscillating when the plate came up. But it stuck perfectly to the plate and no resin was left on the film. I also noticed that the film is not really schratched but is has some pattern, like someone had drawn with a pencil. Any suggestions?

翻譯年糕