Anycubic Photon Printer Owners 造訪社團

原文網址 Alvaro Rodriguez
2020-02-29 22:15:34

Does anyone knows the LCD display tempered glass thickness for OG Photon and S models?

I recall to have read somewhere those are 0.6mm for the OG Photon tempered glass and 1.2mm for the one in the S but no idea if that´s correct though.

Thanks! ?

翻譯年糕

原文網址 Steven Nichols
2020-02-29 21:59:35

So having a few issues ever since swapping from the original photon sliced to the photon workshop. So I then decided to swap to chitu and still having issues ? these are my printer settings. And here’s a pic of the failed print. It’s like the supports weren’t enough but I used heavy supports and a fair few of them too! Any suggestions would be grateful!! My original sliced settings are pretty much the same except for 12 seconds exposure time instead of 8

翻譯年糕

Paul 'Jam' Morris
2020-02-29 22:08:47

Steven Nichols
2020-02-29 22:10:24

Mark Wardle
2020-02-29 22:12:49

Paul 'Jam' Morris
2020-02-29 22:13:35

Steven Nichols
2020-02-29 22:15:00

Paul 'Jam' Morris
2020-02-29 22:24:28

原文網址 Stefan Chao
2020-02-29 21:30:03

Welcome to the Any Family ? got some serious problems I guess...

翻譯年糕

原文網址 Kique Muñoz
2020-02-29 21:27:23

What Anycubic is this? ?

翻譯年糕

Michael Zinski
2020-02-29 21:30:15

Jeff Surma Jr.
2020-02-29 21:37:30

Ivan Fdc
2020-02-29 21:40:25

Ben Wood
2020-02-29 21:51:10

Nino Lumba
2020-02-29 21:54:37

Cannon Rigger
2020-02-29 22:07:02

Cannon Rigger
2020-02-29 22:08:09

Julian Braun
2020-02-29 22:23:28

Pete Kratsch
2020-02-29 22:49:54

Kique Muñoz
2020-02-29 23:38:03

Nesh Imperial
2020-03-01 20:40:10

Serkan Budur
2020-03-01 21:25:50

原文網址 Lorne Bixby
2020-02-29 21:25:14

Has anyone found a way to raise the platform higher when pausing a print...
It pauses so low i can't see the back side of the build plate.
I don't dare remove the plate, lest it doesn't sit exactly where it was when i put it back.

Just had a 15 hour print continue all night a failure i couldn't see.

翻譯年糕

David Newton
2020-02-29 21:48:42

Lorne Bixby
2020-02-29 21:50:25

David Newton
2020-02-29 21:52:02

Lorne Bixby
2020-02-29 21:54:23

Lorne Bixby
2020-02-29 21:54:38

Lorne Bixby
2020-02-29 21:55:00

David Newton
2020-02-29 21:55:08

David Newton
2020-02-29 22:01:33

Lorne Bixby
2020-02-29 22:03:18

Paul 'Jam' Morris
2020-02-29 22:07:07

David Newton
2020-02-29 22:19:22

原文網址 Lorne Bixby
2020-02-29 21:01:06

Does anyone know what might cause this type of mid plate shearing ?
Well supported, run through validator. No islands.
My prints have been dialed in and great lately.
Fep in good condition.
Anycubic grey
.04 layer height
14s exposure
10 layers bottom @ 120 seconds

翻譯年糕

Casey Frank
2020-02-29 21:03:57

Lorne Bixby
2020-02-29 21:07:51

Joe Guillemette
2020-02-29 21:23:33

Lorne Bixby
2020-02-29 21:26:16

Lorne Bixby
2020-02-29 21:26:50

原文網址 Kane Gibson
2020-02-29 20:50:08

What's the best setting for anycubic photon grey resin printing detailed peices What's the best setting for anycubic photon grey resin printing detailed peices 翻譯年糕

Bernie Horowitz
2020-02-29 21:12:31

Chris Wolfe
2020-02-29 21:29:01

Alex Poposki
2020-02-29 21:35:04

Alex Poposki
2020-02-29 21:35:16

Bob Deblier
2020-03-01 04:24:39

Daniel Kottmair
2020-03-01 04:31:32

Eoctek Eduardo
2020-03-01 09:49:42

Eoctek Eduardo
2020-03-01 09:49:55

Harold Crossley
2020-03-01 13:28:01

Richard Humble
2020-03-01 15:15:45

Kane Gibson
2020-03-01 21:45:39

Harold Crossley
2020-03-02 00:19:06

Kane Gibson
2020-03-02 00:19:34

Harold Crossley
2020-03-02 00:33:12

Bernie Horowitz
2020-03-02 08:08:15

原文網址 Dean Eyre
2020-02-29 20:25:08

Well it looks like I've got a dead pixel or two.

Anyone know if there is a better/reliable place to get one from before I go and look on ebay or amazon ?

翻譯年糕

Nipuna Gunarathne
2020-02-29 21:41:29

Justin Lincoln
2020-03-01 08:29:58

原文網址 Eric Weber
2020-02-29 20:18:16

Busy printing and painting DnD miniatures for the starter adventure with the kids......

翻譯年糕

原文網址 Colin Hughes
2020-02-29 20:15:26

Is anyone else having issues with the new .20 version of tte photon software not creating auto supports. Even when I have 10 ot the same item it only put supports under 3 or 4.

翻譯年糕

討論主題

發文排行榜

回文排行榜

熱門關鍵字