Anycubic Photon Printer Owners 造訪社團

原文網址 Bob Martin
2019-06-02 23:28:50

was curious to see how voronoi model would print... not bad I guess

翻譯年糕

Graham Clements
2019-06-03 01:46:12

原文網址 Andrew Chan
2019-06-02 23:23:12

S-printed Fat Thor complete. Is he sleeping?

翻譯年糕

Jay Gustavo Mclean
2019-06-02 23:24:00

Bernardy L
2019-06-02 23:27:50

Dick Teh
2019-06-03 00:26:04

Katon Setiawan
2019-06-03 00:45:59

Kristjan Kallas
2019-06-03 00:53:23

Peter Hansen
2019-06-03 01:27:50

Emilio Micheletti
2019-06-03 02:46:48

Andrew Chan
2019-06-03 02:57:47

Steve Sanford
2019-06-03 03:51:04

Shane Bui
2019-06-03 06:44:28

Mark A. Siefert
2019-06-03 08:18:29

Nicolas Tsagarides
2019-06-03 17:00:35

原文網址 Gavin Mccool-Solis
2019-06-02 23:23:08

Anyone know of a Safety Yellow resin?

翻譯年糕

Dave Corbett
2019-06-04 15:46:11

Dave Corbett
2019-06-04 15:48:19

原文網址 Maggie Jenner-Bennett
2019-06-02 23:02:21

I just pulled these off the printer and I'm getting some defects that I don't understand. There were some flat bits of resin in there that were delicate enough they didn't survive the IPA wash too. This printer has also been leaving a shadow of resin behind on the FEP that I need to clean off after every print (that's been happening for a while). Any ideas? The print I did just before this batch showed no such lines and looks good.

翻譯年糕

Maggie Jenner-Bennett
2019-06-02 23:05:08

Maggie Jenner-Bennett
2019-06-02 23:06:00

Wesley Dowell
2019-06-02 23:13:39

Maggie Jenner-Bennett
2019-06-02 23:14:53

Maggie Jenner-Bennett
2019-06-02 23:17:08

Maggie Jenner-Bennett
2019-06-02 23:17:57

Andrey Sabrev
2019-06-02 23:29:08

Wesley Dowell
2019-06-02 23:30:55

Stefan Giudici
2019-06-03 02:02:15

Gary Houser
2019-06-05 03:13:44

Maggie Jenner-Bennett
2019-06-05 03:17:39

原文網址 Tamás Lehoczky
2019-06-02 22:50:13

Hope you don't mind me spamming the group, but maybe I've found why my prints are constantly failing - the build plate cannot be leveled. I move it down, thin paper can be removed but resists, press z=0, Confirm...then press Home, and it still goes higher than before, there's about a millimeter between the LCD and the build plate.

I'm getting really bloody frustrated.

翻譯年糕

Andy Huffer
2019-06-02 22:51:47

Danny Lloyd
2019-06-02 22:52:33

Tamás Lehoczky
2019-06-02 22:53:21

Andy Huffer
2019-06-02 22:53:38

Danny Lloyd
2019-06-02 22:53:54

Tamás Lehoczky
2019-06-02 22:53:55

Tamás Lehoczky
2019-06-02 22:55:59

Danny Lloyd
2019-06-02 22:57:16

Tamás Lehoczky
2019-06-02 22:58:30

Andy Huffer
2019-06-02 23:05:29

Andrey Sabrev
2019-06-02 23:08:38

Tamás Lehoczky
2019-06-02 23:10:06

Andrey Sabrev
2019-06-02 23:13:14

Art Barrow
2019-06-02 23:26:14

Tamás Lehoczky
2019-06-02 23:31:13

Art Barrow
2019-06-02 23:35:09

Tamás Lehoczky
2019-06-03 03:57:19

Tim Moulton
2019-06-03 04:35:56

原文網址 Georgios Kolotouros
2019-06-02 22:48:27

Fidel castro ,model : gkhellas , dragon resin grey

翻譯年糕

Georgios Kolotouros
2019-06-03 07:33:12

Fanis Kapa
2019-07-19 16:09:51

Georgios Kolotouros
2019-07-19 20:08:03

Fanis Kapa
2019-07-20 02:11:14

Georgios Kolotouros
2019-07-20 03:48:21

Georgios Kolotouros
2019-07-20 03:48:43

Georgios Kolotouros
2019-07-20 03:49:42

Georgios Kolotouros
2019-07-20 03:53:13

原文網址 Tiago Duarte
2019-06-02 22:47:45

Before and after , Cast with white gold , finished with topázio stones (before rhodium, the piece Will bight )

翻譯年糕

原文網址 Garrett Kvåle
2019-06-02 22:30:09

Hey hive mind!
Have a couple questions. I printed this awesome model that is a functional whistle. While playing it I thought this could make an amazing looking pipe.

Question 1. How difficult would it be modifying the existing STL into a pipe (base idea pic below).

Question 2. I would have a hole up top for a glass bowl to fit in so no flame hits the plastic, though still curious what the heat tolerance of the resin is?

翻譯年糕