Anycubic Photon Printer Owners 造訪社團

原文網址 Luke Mason
2019-04-19 20:13:32

I have not bought this, but discovered while mindlessly browsing

1L bottles of 405nm UV resin. Variety of colours.

翻譯年糕

原文網址 Chris Visser
2019-04-19 20:13:05

Nick - Here's the cleaned up result of that Paladin.

Hollowed - 1mm and holes in feet and head (feet holes ended up getting blocked but didn't seem to cause an issue).

Anycubic Green - T 0.04, E: 8s, O: 4.5, BE: 50s, BL: 8

Turned out fine. Did the supports in B9 and the came off very easily.

翻譯年糕

Chris Visser
2019-04-19 20:13:33

Chris Visser
2019-04-19 20:14:21

Chris Visser
2019-04-19 20:14:32

Chris Visser
2019-04-19 20:14:43

Nick Williams
2019-04-19 23:19:44

Nick Williams
2019-04-19 23:21:00

Koie Smith
2019-04-19 23:43:11

Koie Smith
2019-04-19 23:46:34

Chris Visser
2019-04-20 04:46:03

Chris Visser
2019-04-20 04:47:18

Chris Visser
2019-04-21 10:39:07

Chris Visser
2019-04-21 10:39:25

Chris Visser
2019-04-21 10:39:40

Chris Visser
2019-04-21 10:39:53

Chris Visser
2019-04-21 10:40:31

原文網址 Alex Martin
2019-04-19 20:09:56

Hi guys. Very new to DLP so forgive any noob questions. I printed a rook in anycubic grey and I'm not sure if I'm just expecting too much of the machine or if there are some print quality issues going on. There seems to be some very slight bumpy layers and also the text is not as sharp as I would have hoped.

翻譯年糕

Bob Deblier
2019-04-19 20:57:39

Alex Martin
2019-04-19 20:58:50

Bob Deblier
2019-04-19 21:03:21

Bob Deblier
2019-04-19 21:05:11

Alex Martin
2019-04-19 21:54:53

Jonathan Hall
2019-04-20 10:30:26

Jeremy Wolff
2019-04-20 12:25:08

原文網址 Marcin Rzycki
2019-04-19 19:10:34

https://www.thingiverse.com/thing:3574266
This is my design. Hope You will like it!

翻譯年糕

Chris Comeau
2019-04-19 19:12:20

Johnson Yeh
2019-04-19 19:21:56

Marcin Rzycki
2019-04-19 19:28:30

Johnson Yeh
2019-04-19 20:58:32

Jason Kelly
2019-04-19 21:19:36

Marcin Rzycki
2019-04-20 00:58:27

原文網址 Jim Monty
2019-04-19 18:50:27

Hi All,

noob here. im about to embark on my first print. im using the sample anycubic green. my object is 11mm in length and 2 cm tall. its basically a hollow rectangle with 3mm walls and holes on sides to take up less resign and also less suction. ideally i would like to print it flat rather than 45 degrees because of build time.

my proposed setting are layer height .05mm

bottom count 8
ex tim 10
bottom ex time 50
light off 4.5 (its the yellow window printer bought around xmas time)
bottom light off 0

i am using chitubox auto-supports for it but would like your assessment if anything is glaringly wrong

翻譯年糕

Chris Visser
2019-04-19 19:01:03

Jim Monty
2019-04-19 19:01:34

Chris Visser
2019-04-19 19:04:30

Jim Monty
2019-04-19 19:11:46

Jim Monty
2019-04-19 19:57:13

Jim Monty
2019-04-19 19:57:56

原文網址 Vincent Ramos
2019-04-19 18:32:45

So I'm having a strange problem. I have multiple items to print and onlya couple will form. Below is the image getting UV and then the end results. This has happen on multiple prints even after I reslice the files. I’m using a stick photon and stock settings from the slicer. I’m using anycubic green resin.

Also some of prints from the same sole will result in more prints. Sometimes somethings forms on the film where the item was suppose to be and other times nothing.

翻譯年糕

原文網址 Ken Acorda
2019-04-19 18:12:26

Hi guys, newbie here. I just got my Anycubic Photon and tried the model that comes from the usb and copied it to a new usb. Unfortunately I didn’t get successul result on my first print. Also followed the instruction on levelling the build plate. Am I missing something here?
Thanks!

翻譯年糕