Anycubic Photon Printer Owners 造訪社團

原文網址 Eric Wilfreesboro
2019-04-04 11:25:13

Heater electrical done... gotta reprint housing now. :)

翻譯年糕

Eric Wilfreesboro
2019-04-04 11:38:32

Eric Wilfreesboro
2019-04-04 11:39:28

Robert Silvers
2019-04-04 12:33:59

Alex Varley
2019-04-04 16:09:35

Eric Wilfreesboro
2019-04-04 19:53:05

原文網址 Sergio Nunes
2019-04-04 11:25:00

This FEP scratch for sure will impact on my prints, right? I think I did that when using the scrapper to remove some cured resign from it.

翻譯年糕

Kevin Reynolds
2019-04-04 11:29:08

Ryan Cook
2019-04-04 11:30:31

Sergio Nunes
2019-04-04 11:48:09

Silas Bo Nielsen
2019-04-04 17:07:15

原文網址 Bud Hansen
2019-04-04 10:19:09

What resin can handle the temperature of pewter???

翻譯年糕

Bud Hansen
2019-04-04 10:20:40

Stefan Giudici
2019-04-04 12:24:44

Khoa Truong
2019-04-04 15:28:53

Jacek Anyszkiewicz
2019-04-04 16:12:28

Bud Hansen
2019-04-05 10:22:55

Julia von Pfaler
2019-04-05 18:39:32

Bud Hansen
2019-04-06 10:17:47

原文網址 Parham Bridges
2019-04-04 09:42:57

Any of you guys run your printer in the garage? That is my plan but I didn't know if the heat in the summer would be a problem for the printer or the resin or alchohol out there. It gets to maybe 100 here during the worst part of the summer.

翻譯年糕

James Cachia-Garrett
2019-04-04 11:26:19

原文網址 James Lockwood
2019-04-04 08:52:30

Has anyone ever seen an stl even remotely close to this?

翻譯年糕

James Lockwood
2019-04-07 04:12:18

原文網址 Jason Snell
2019-04-04 07:23:07

I think my prints are allergic to primer. They look all smooth and clean after I remove the supports. Then I spray primer on and all these bumps and dimples appear.

翻譯年糕

Orwin SantaCruz
2019-04-04 07:26:09

Stefan Giudici
2019-04-04 07:41:03

Jason Snell
2019-04-04 07:51:14

Jesus Aquino
2019-04-04 12:57:37

Andrew Chan
2019-04-04 14:51:39

原文網址 John VanRyn
2019-04-04 07:13:21

ok it is in the mail.. so.. slicing/supports/etc.. should I use stock software and auto supports? should I place them myself? what is the PhotonFileValidator and how/why should I use it?

翻譯年糕

原文網址 Arman Kussainov
2019-04-04 07:09:25

Hello guys,

maybe someone have Stl model from this guy?

翻譯年糕

Rod Williams
2019-04-04 13:26:27

原文網址 Jason Gill
2019-04-04 06:22:21

Just printed some engine inserts for the Revell Star Wars Venator model.
They are on Shapeways but they couldn't print so the author was nice enough to sell me the STL's.
I only had their clear green but once painted will be fine. Perfect fit too. The smaller ones, ruler for scale, are so cool!!!
The kit will be lit too.

翻譯年糕

原文網址 Kory Sebby
2019-04-04 06:00:13

Any chance anyone have a stl file for golf clubs / and or bag?

翻譯年糕

討論主題

發文排行榜

回文排行榜

熱門關鍵字