Anycubic Photon Printer Owners 造訪社團

原文網址 Fred Breton
2019-02-03 10:55:57

One of the latest Francesco A. Pizzo's sculpts. Done with Monocure Rapid White and dye pigments.

https://www.patreon.com/user?u=887432

翻譯年糕

原文網址 Rob Mayberry
2019-02-03 10:48:06

Comming along

翻譯年糕

Hector Felix
2019-02-03 10:51:23

Rob Mayberry
2019-02-03 10:59:25

原文網址 Tony Luong
2019-02-03 10:34:24

If I'm sharing too much... It's cause I'm obsessed with this stupid printer ? ? . Here are a few more of the recent prints.

翻譯年糕

原文網址 Nicky Rossouw
2019-02-03 10:24:33

Hey guys, I know there are some pretty sick 3D designers in this group and I was after some advice.
My friends recently got engaged and I wanted to print them a pendant each, but I thought if I could somehow incorporate a lithophane into the internal walls of the pendant that would be really cool... any thoughts of how I might go about this? (I have a decent amount of experience with fusion360, as well as a little with meshmixer)
TIA

翻譯年糕

Mark Wardle
2019-02-03 10:31:07

原文網址 Hosung Kim
2019-02-03 09:50:49

I have been just working with the default .05 setting. How hard it is to print .025? You know when you lower the setting for FDM, it gets hard to print, is it the same with DLP?

翻譯年糕

Chris Hunt
2019-02-03 09:55:55

Clint Primley
2019-02-03 10:21:33

Jim Leenan
2019-02-03 10:24:18

Stefan Giudici
2019-02-03 10:36:02

Arizeta Zaft Aeug
2019-02-03 10:39:39

Robert Silvers
2019-02-03 12:14:39

Darren Tarbard
2019-02-03 17:47:26

原文網址 Steve Nicholls
2019-02-03 09:40:14

Kratos at 0.025 layer height. Monocure Rapid Grey. First test at these settings

翻譯年糕

Redgrund Tready
2019-02-03 11:58:16

Paweł Grochowski
2019-02-03 12:37:44

Thanh M. Vu
2019-02-03 12:38:22

Steve Nicholls
2019-02-03 12:53:25

Robert Silvers
2019-02-03 12:56:22

Steve Nicholls
2019-02-03 12:57:33

Robert Silvers
2019-02-03 12:58:03

Steve Nicholls
2019-02-03 12:59:32

Robert Silvers
2019-02-03 12:59:59

Steve Nicholls
2019-02-03 13:01:25

Robert Silvers
2019-02-03 13:20:44

Shawn Clifton
2019-02-03 20:02:10

Michael Allen
2019-02-03 20:35:42

Sen Kun
2019-02-03 20:51:43

Kelvin Pang
2019-02-03 21:02:21

Daniel Amaral
2019-02-03 23:03:29

Dave Williams
2019-02-04 06:42:04

Steve Nicholls
2019-02-04 07:38:58

Dave Coggan
2019-02-04 17:49:04

Travis Hunt
2019-02-23 11:06:56

Steve Nicholls
2019-02-23 11:54:13

原文網址 Chip Van Gilder
2019-02-03 09:07:09

Real close to a maximum capacity print. 15 hours. On30 flat car frame.

翻譯年糕

Keith Fothergill
2019-02-03 09:12:22

Jonathan King
2019-02-03 10:31:44

Chip Van Gilder
2019-02-03 10:40:31

Chip Van Gilder
2019-02-03 10:42:02

Alessandro E. Danti
2019-02-04 08:00:40

Chip Van Gilder
2019-02-04 08:15:55

Mitchell Kruik
2019-02-04 08:33:23

Mitchell Kruik
2019-02-04 08:36:21

Chip Van Gilder
2019-02-04 11:53:10

原文網址 Marc Fischer
2019-02-03 08:55:09

Nux's bobblehead, but tiny. Spring is from a pen then fused all 3 pieces with resin.

翻譯年糕

Dodo Kovacs
2019-02-04 07:11:30

Marc Fischer
2019-02-04 07:32:12

原文網址 Dylan Hancox
2019-02-03 08:19:41

I just started a print with 4 humans around 4 inches tall. i then realised it would probably print a lot better if they were printed upside down? do you normally print people uoside down?

翻譯年糕

Richard Shapiro
2019-02-03 08:43:40