Anycubic Photon Printer Owners 造訪社團

原文網址 Michael Fox
2019-01-15 06:03:50

Any thoughts on what caused the vertical lines the in the upper left of the litho? There's one on the forehead also. They are not in the stl. It was printed vertically on the long side. Sliced at .04

翻譯年糕

Aiden Sone
2019-01-15 06:09:34

Jannick Langfahl
2019-01-15 06:09:57

Michael Fox
2019-01-15 06:10:02

Aiden Sone
2019-01-15 06:10:20

Michael Fox
2019-01-15 06:10:41

Fred Breton
2019-01-15 09:44:34

原文網址 Rasmus Jansson
2019-01-15 05:52:28

Mr Big in almost max size.. and the small guys.. in wanhaoo clear(?) isn’t that a little bit false marketing? Should be sold as “light yellow”

翻譯年糕

Eric Gauthier
2019-01-15 05:59:27

Stefan Giudici
2019-01-15 06:02:22

Andrew McKay
2019-01-15 06:05:58

El Ner Endem
2019-01-15 06:12:21

Rasmus Jansson
2019-01-15 06:13:36

Benjamin Davis
2019-01-15 06:38:47

Gustaf Sjögren
2019-01-15 19:45:52

Andrew McKay
2019-01-15 20:38:21

Rasmus Jansson
2019-01-17 02:28:06

原文網址 Marcus Leander
2019-01-15 05:43:14

Hello, I'm a total noob when it comes to 3d-printing and I have a question. I resently got my anycubic photon and I've tried a few prints. The models have turned out great. But, there are always som cured to semi cured resin left on the FEP. And because of that I feel like I have to clean the vat between every print. What could be the cause/causes of the resin build up on the FEP?

翻譯年糕

Jim Branham
2019-01-15 05:48:42

Dustin Scott
2019-01-15 05:51:48

Stefan Giudici
2019-01-15 05:52:32

Marcus Leander
2019-01-15 06:00:13

Marcus Leander
2019-01-15 06:03:00

Richard Shapiro
2019-01-15 06:52:12

Simon Powell
2019-01-16 01:40:53

Robert Silvers
2019-01-16 01:43:47

Sen Kun
2019-01-16 02:28:39

Marcus Leander
2019-01-16 05:10:08

原文網址 Mike Mchughes
2019-01-15 05:39:59

Hi all. Are supports inside of hollowed objects usually necessary? They seem to just be giving me large unsupported islands in the validator, and its hard to look around inside the object. Also, does this seem set up well? I've got holes in the feet and on the back of the neck Thanks.

翻譯年糕

Mike Mchughes
2019-01-15 05:40:40

Mark Wardle
2019-01-15 05:43:20

Mike Mchughes
2019-01-15 05:45:58

Mark Wardle
2019-01-15 05:48:26

Mike Mchughes
2019-01-15 05:51:19

Lucas Azd
2019-01-15 06:34:51

原文網址 Will Koone
2019-01-15 05:23:45

Hello people of the resin printing world. I am a new traveler to this land. :) Been running FDM machines for years and took the leap into resin with the photon. So far 2 prints down (including the cube that comes with it). Enough to learn I have stuff to learn. is there any guideline for creating your own supports outside of the photon software? (length vs diameter, spacing, what angles need support ect)?

Also already learned the hard way, do not clean FEP with IPA. Any other common pitfalls I should worry about?

翻譯年糕

Marcus Leander
2019-01-15 05:48:45

Will Koone
2019-01-15 05:49:59

Marcus Leander
2019-01-15 05:50:35

Will Koone
2019-01-15 05:51:46

Marcus Leander
2019-01-15 05:59:23

Will Koone
2019-01-15 06:01:37

Nemo Vilpponen
2019-01-15 06:05:31

Alex Vee
2019-01-15 06:09:24

Will Koone
2019-01-15 07:14:22

Scott Gardner
2019-01-15 07:25:46

Richard Shapiro
2019-01-15 07:40:54

Jon Piercy
2019-01-15 07:46:45

Alex Vee
2019-01-15 16:54:54

Robert Silvers
2019-01-17 14:13:58

Holden8702
2019-01-17 14:42:22

原文網址 Corey Hallgren
2019-01-15 05:00:15

Anyone have settings they're willing to share for 0.1 layer hight using either the anycubic green or anycubic black resin?

Thanks in advance!

翻譯年糕

Vinicius Silva
2019-01-15 05:03:28

原文網址 Nemanja Lacedaemon Enomotarch Đe
2019-01-15 04:29:55

Hi.I finaly changed my graphic card and instal slicer but now I have one question(I am beginer) .where in slicer I can enter dimension like I need of my model for print? Tnx :)

翻譯年糕

Richard Shapiro
2019-01-15 04:45:52

Richard Shapiro
2019-01-15 04:51:09