Anycubic Photon Printer Owners 造訪社團

原文網址 Kevin McGuigan
2019-01-14 06:26:27

Moon city on the photon ?

翻譯年糕

Jared Petersen
2019-01-14 22:52:41

Kevin McGuigan
2019-01-15 01:12:06

原文網址 Kevin McGuigan
2019-01-14 06:14:48

Whats your longest print times?
My longest print so far....
20+hrs in, still 3.5hrs to go.
Using Çağrı Aydoğan dragon resin test sample.
Print settings: 0.03 layers @ 10 sec
90sec bottom layers
Manual supports.

翻譯年糕

Fred Breton
2019-01-14 06:32:23

Gon Garcia
2019-01-14 10:00:04

Kevin McGuigan
2019-01-14 11:01:32

Joshua Allan Riddick
2019-01-16 06:59:54

Kevin McGuigan
2019-01-16 10:56:39

Richard Shapiro
2019-01-16 11:01:43

Bryan Mikolajewski
2019-01-16 11:13:43

原文網址 David McGyver
2019-01-14 06:03:28

Hey folks, does anyone have advice on printing dimensionally correct parts? I'm trying to make a mobile phone mount for my car that's in 3 parts: One that goes on the phone, one that goes on a car windscreen bracket, and one that I can use as a belt clip.

My issue at the moment is that I'm trying to print holes for 10mm by 3mm magnets to hold the phone in place when it's either on the belt or in the car, and they're coming out the wrong size. Initially they seem OK, and are a reasonably snug press-fit which is what I was going for, but over 24-48 hours the parts seem to shrink further, and crack themselves open on the magnets. The part itself (once the interesting bits are excluded) is basically just a 60mm by 22mm by 5mm thick slab of acrylic.

Resin is the Monocure Black, I'm using 5x80s bottom layers, then 13 second mid-layers at 50 um.

I've seen a couple of references to shrinkage at ~3%. Should I just be scaling all my parts at 103% in the slicer to account for that? Would that actually work?

It's kind of important as I've done a full design for a magnetically coupled impeller pump I want to print off to stir my wash-vats, but that design uses bearings so I need those prints to come out bang-on the right size.

翻譯年糕

Dustin Scott
2019-01-14 06:08:07

Robert Silvers
2019-01-14 06:53:55

Robert Silvers
2019-01-14 07:36:20

Robert Silvers
2019-01-14 07:36:52

David McGyver
2019-01-15 09:54:46

原文網址 Velvet Mark
2019-01-14 05:56:40

Printing off a few Elite Dangerous ships:)

For less than £20 of resin.

Most of them printed at 90 degrees from the print bed, with light supports. 25 microns. Amazon Green dental casting resin that I got by mistake. I thins the resin takes ages to cure under UV but the detail is good. Love this machine!

翻譯年糕

Mark Wardle
2019-01-14 06:04:34

Mark Wardle
2019-01-14 06:06:10

Velvet Mark
2019-01-14 06:10:00

Brian Young
2019-01-14 06:12:35

Velvet Mark
2019-01-14 06:12:57

Velvet Mark
2019-01-14 06:13:58

Mark Wardle
2019-01-14 06:14:20

Velvet Mark
2019-01-14 06:14:56

Mark Wardle
2019-01-14 06:15:13

Velvet Mark
2019-01-14 06:16:13

Velvet Mark
2019-01-14 06:17:55

Brian Young
2019-01-14 06:20:20

Mark Wardle
2019-01-14 06:20:20

Velvet Mark
2019-01-14 06:21:40

Velvet Mark
2019-01-14 06:24:07

Mark Wardle
2019-01-14 06:25:28

Mark Wardle
2019-01-14 06:25:51

Velvet Mark
2019-01-14 06:30:05

Brian Young
2019-01-14 06:32:26

Velvet Mark
2019-01-14 06:34:06

Mark Wardle
2019-01-14 06:34:16

Arne Gruppe
2019-01-14 06:34:23

Velvet Mark
2019-01-14 06:34:58

Velvet Mark
2019-01-14 06:35:07

Mark Wardle
2019-01-14 06:35:28

Velvet Mark
2019-01-14 06:36:00

Mark Wardle
2019-01-14 06:36:23

Mark Wardle
2019-01-14 06:36:51

Mark Wardle
2019-01-14 06:38:25

Mark Wardle
2019-01-14 06:40:30

Zac Morris
2019-01-14 06:48:47

Ekaterina Vitalyevna
2019-01-14 07:28:04

Velvet Mark
2019-01-14 07:29:01

Velvet Mark
2019-01-14 07:32:20

Velvet Mark
2019-01-14 07:42:37

Ekaterina Vitalyevna
2019-01-14 09:32:25

Jacob Townsend
2019-01-14 19:28:37

Ian Adams
2019-01-14 19:39:59

Velvet Mark
2019-01-14 20:52:08

Sen Kun
2019-01-14 21:19:25

Velvet Mark
2019-01-15 01:00:05

Sen Kun
2019-01-15 01:06:16

Velvet Mark
2019-01-15 02:53:46

原文網址 Peter Ede
2019-01-14 05:41:14

Installed new fep last week. Had to replace yesterday due to failed prints.
Some how it managed to get quite a large hole.
No idea why.

翻譯年糕

Matt Tilson
2019-01-14 08:22:59

Jannick Langfahl
2019-01-14 15:49:38

原文網址 Thomas Salavert
2019-01-14 05:31:24

Hi everyone ! Thank you for accepting me :) Really fond of 3d printers (and working in the 3d field in Belgium even if its difficult). How far can I go with the layer thickness setting. Didn't touch anything for now (so 0,5 mm by default) and the result are just mindblowing for me. Didn't try more coz I wait for more resin to come.