Anycubic Photon Printer Owners 造訪社團

原文網址 Aiden Sone
2019-01-13 06:59:56

I'm planning to make the rear 4" vent for ventilation, but i'm unsure if its possible to produce on the Photon. In the software, it appears it will fit the build plate in a vertical orientation. Would this work? I'm guess I'll need a ton of supports on any of the horizontal surfaces, including inside the 4" opening.

Any advise before trying this would be appreciated.
Thanks.

翻譯年糕

Paul Drinkut
2019-01-13 07:41:20

原文網址 Mark Wardle
2019-01-13 06:40:58

Its that time of the week again. and we have a lot of new users. so this video should help with the basics of hollowing out models and adding vents to the model. how to fix models so they can be printed with resin. how to add supports. and more. all the software used is free. hope this helps new users get started.

翻譯年糕

原文網址 Brian Young
2019-01-13 06:32:23

Stress cube success ?

翻譯年糕

原文網址 Ben Hawker
2019-01-13 06:22:22

Has anyone had this problem it started a print then stopped fan went off now won't move at all

翻譯年糕

Andirlik Rawdow
2019-01-13 06:38:34

Kaylee Rivera
2019-01-13 06:52:41

Trevor Adams
2019-01-13 09:30:04

Ben Hawker
2019-01-13 09:30:49

Trevor Adams
2019-01-13 09:31:22

Ben Hawker
2019-01-13 09:32:45

Eric Spray
2019-01-13 10:16:59

Sen Kun
2019-01-13 17:22:29

Ben Hawker
2019-01-13 17:23:00

Sen Kun
2019-01-13 17:24:55

Ben Hawker
2019-01-13 17:26:16

Ben Hawker
2019-01-13 18:54:34

原文網址 Bob Heron
2019-01-13 06:20:49

And second set done, awesome simply awesome Evan you rock. I lost a wheel down the sink when I was washing them lol. I have no idea what the ghosting of the wheels is from.

翻譯年糕

原文網址 Dillon Olney
2019-01-13 06:14:30

I feel like this base/raft is suuuper thick... thoughts?

翻譯年糕

Peter Bolger
2019-01-13 06:16:52

Mark Wardle
2019-01-13 06:46:12

Dillon Olney
2019-01-13 06:47:49

Mark Wardle
2019-01-13 06:50:09

Mark Wardle
2019-01-13 06:51:36

Joel Ligeiro
2019-01-13 07:14:01

Mark Wardle
2019-01-13 07:15:05

Seona van der Pol
2019-01-13 08:50:35

原文網址 Andy Furnass
2019-01-13 06:12:58

I've already printed dozens of things using Photon slicer without any problems. Now when I try this item and look in the viewer, half of the model (solid side of an office type container printed flat( side with window and door, both ends, door, window frame and top printed ok))on a diagonal is missing!!!. Tried in Chitubox, Set as Photon. Programmed the same settings for resin (Photocentric grey) Said print was going to take 1hr 30min, same as other parts. Checked viewer, no bits missing, Print took 12 min and only printed top few layers which are totally unusable. Please help. What have I missed.

翻譯年糕

Stewart Ralph
2019-01-13 06:53:14

Patrick Smith
2019-01-13 07:09:15

Andy Furnass
2019-01-13 07:59:11

Andy Furnass
2019-01-13 08:00:09

Bob Heron
2019-01-13 09:43:13

Stewart Ralph
2019-01-14 09:35:47

原文網址 Jed Jeng
2019-01-13 05:53:35

Hey photoners! Sometimes my printer just stops mid print. The fan turns off and I am also unable to command the build plate from the menus. Anyone else run into this issue? Thanks!

翻譯年糕

Emanuele Ferraro
2019-01-13 06:10:55