Anycubic Photon Printer Owners 造訪社團

Hello everybody!

Afther Printing I clean whit isopropyl.... But the print Afther cleaning don't stick so well to the platform.... Any tips?

翻譯年糕

Okay here's the second try with the new settings I got most of it to stay on the bed I check the level maybe I just didn't get it level enough. But then again I'm being told to tip each one at an angle so possibly that will fix it? Maybe I didn't make the support long enough?

翻譯年糕

Hey guys, i dont know if u can see that in pictures, i just noticed the left rail is slightly detached from the carrier. The right one seems perfectly in position. By rails im refering to the steel tubes that the carrier uses as grooves to slide up and down

翻譯年糕

Has anyone had any success with networking the Photon? I did a search and found some info about the internal network port but the link in it is dead.

Sorry if this is something that has been answered, I searched and could not find a lot of info.

翻譯年糕

printer arrives Friday and cant wait ordered some elegoo gray and blue. Hope its a good compliment to my cr10.

Any guides I can read up on to prepare?

翻譯年糕

hi guys, i had a semi successfull print with some weird issue that i don't really know what to think of or do about it. As you can see i manage to print 2 out of 3 deers without support, the failed one was way too small to stick on the plate (legs smaller than light support). The little one grew up on one leg only, nonetheless, what succeded on the little one is without any deffect. On the bigger one i had one clump(probably from the failed legs) attached on the rear leg and one on the nose, both easy to remove. Everything up to the head printed perfectly, but the antlers look shifted every here and there, wich i don't really understand why?
Finally, when i got to clean the vat, all deer spaces all had full contour cured stuck to it (i really wonder how the light got through to finish the bigger deer). My fep is still pretty clear without any dents.
I printed since then (in monocure rapid black) and all the pieces went well except for the right leg that has a nasty scar..
please give me your opinion, i'm fairly ascustomed to others problem on this page but couldn't really diagnose my case...
heres the setup:
anycubic green
exposure: 8s
base exposure: 60s
base layers: 8
layer height: 0.05
room temperature: 23°C
little model full
big model kinda hollow( voronoi, antlers mostly full)

翻譯年糕

Hi all, just got delivery of a 1ltr bottle, and it has a past date stamped on it, is it the date the resin was made or the expiry? If its the latter, then it puts the resin out of date!

翻譯年糕

Hello guys. I just got my anycubic photon yesterday and tried twice the test cube and failed.

The first time I thought I did miss something on the calibration. So i recalibrate the bed for the second print. However it still fail similarly.
There are some minor scratches on the FEP.

Is the bubble between screen and FEP matter? I did clean the screen and the bottom of the vat with ISO alcohol.

Any suggestions for this type of problem?

edit: I did stop it in 70-80% print time. since the fail quite visible and no point to continue printing.

翻譯年糕

I could use some reasons why the downloaded presliced cube was a partial failure. Here are pictures I took this morning. I started another print with the suggested settings Google doc, on the assumption that they just didn't slice it well, but would like to hear from more experienced people.

翻譯年糕

Hello everyone i just got my photon and preparing for a test print. I want to ask somethig to you. I want to put the printer on a balcony becouse i dont have much room inside. It's cold outside like 0C° Did anyone tested printing in low tempetures?

翻譯年糕